valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
5,819,789 HOT COLD Turn off hot and cold water CAUTION supplies before beginning. Installation Instructions 2064.451 ROUGHING-IN DIMENSIONS 1 2" D. (52mm) 1" (25mm) 2" MIN. (51mm) 3" MAX. (76mm) MAX. FINISHED WALL FINISHED WALL 2" D. (52mm) 9-1/4" (235mm) 1/2" NPT INLETS 8" (203mm) 4" CROSS (102mm) HANDLE 1 INSTALL VALVE BODY Determine where the finished wall location will be. This measurement is very important! Note: The rough-in measurement from the finished wall is; 2" minimum and 3" maximum. This is a 1" tolerance. See rough-in illustration above. Secure FAUCET BODY (1) to cross brace of wall structure at required height using two wood screws. Turn valves to off position. Turn hot and cold supplies on and check fitting connections for leaks . Complete wall construction. WOOD SCREWS HOT COLD CROSS BRACE WALL STUDS 16" MAXWALL MIN1-5/8"DEEP MAXWALL MIN1-5/8"DEEP Connect HOT water supply to left VALVE inlet and COLD water supply to right VALVE inlet. Use pipe sealant or Teflon tape for all threaded connections. For sweat connections, do not make sweat connections directly to valve body. Damage to seals and and valve cartridge may occur. Required Tools Flat Blade Screwdriver Adjustable Wrench Channel Locks 2-1/8" D. (54mm) 2" MAX. (51mm) MAX. 1-1/4" O.D. (32mm) O.D. Pipe Wrench Teflon Tape Plumbers' Putty or Caulking Tubing Cutter WALL MOUNT FAUCET IN-WALL LAVATORY FITTING SERIN™ To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. M968852 Rev.1.3 4 3 INSTALL HANDLES GROOVE GROOVE FINISHED WALL 1 1 4 8 9 5 6 7 4 2 DRAIN INSTALLATION Assembly GASKET (2) WASHER (3) and LOCKNUT (4) onto DRAIN BODY (1). Tighten LOCKNUT (4) firmly. Assembly TAILPIECE (5) to DRAIN BODY (1). Apply a bead of PUTTY to underside of FLANGE on DRAIN BODY (1). Feed DRAIN BODY (1) down through lavatory. LAVATORY PUTTY 2 3 4 5 1 2 INSTALL WALL SPOUT Remove PLASTER GUARDS (1) from valve bodies. Inspect that SPOUT NIPPLE O-RING (2) is seated in groove of SPOUT NIPPLE (3). Thread SPOUT MOUNT (4) onto SPOUT NIPPLE (3). Align groove on SPOUT MOUNT (4) with face of finished wall. See Figure A. Install SEAL (5) into SPOUT ESCUTCHEON (6). Place SPOUT ESCUTCHEON (6) with SEAL (5) onto SPOUT MOUNT (4). Push SPOUT (7) onto SPOUT MOUNT (4). Align SPOUT (7) and tighten SPOUT SET SCREW (8) with 3mm HEX WRENCH (9) supplied. Figure A 1 MAXWAL MIN1-5/8"DE MAXWALL MIN1-5/8"DEEP 3 1 5 2 3 4 Thread HANDLE BASE (4) onto HANDLE ESCUTCHEON (3) until seated tightly against HANDLE ESCUTCHEON (3). Place O-RING (2) into HANDLE ESCUTCHEON (3). Thread HANDLE ESCUTCHEON (4) onto VALVE (5) until snug against finished wall. Turn VALVE STEMS (1) to off position. 5 SERVICE 3 To change direction of handle rotation, 4 proceed as follows: Turn valve to OF...
Questo manuale è adatto anche per i modelli :Plumbing - SERIN M968852 (219.1 kb)
Plumbing - SERIN M968852 (219.1 kb)
Plumbing - SERIN M968852 (219.1 kb)