*Your new American Standard faucet is designed to work only with the Speed Connect drain. Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Speed Connect™ Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. Turn off water at CAUTION main supply. INSTALL

mounting surface thickness 1 1/8" Hole sizes in mounting surface Spout 1 3/8" Valves 1 1/4" Max. incoming water pressure 145 PSI Recommended incoming water pressure 22 - 72 PSI Max. incoming hot water temp. 176°F* Recommended incoming hot water temp. 120° - 140°F* Max. flow rate -- lavatory faucets 2.2 gpm Max. flow rate -- bidet faucet 2.2 gpm The bidet faucet is not suitable for use on vertical spray bidets. This faucet may be used with a continuous flow water heater if the flow pressure is at

These strips must be removed before the spout is installed. Loosen the spout screw with a 2.5 mm Allen wrench.Pull the spout away from the escutcheon. Remove the adhesive strips. Reassemble the spout assembly so that the hole for the pull rod is at the rear of the spout. adhesive strips Installation Remove the valve mounting nuts from the valves. From below the mounting surface, push the valves up into the holes. Install the mounting nuts on the valves. Tighten the tensioning screws. Place the h

for CP43A2003) (3 Signals/Rev. for CP43D2001) Specifications Model No. Working Voltage (V) Rated Voltage (V) Max Water Head m-H.O Max Flow Rate ml/min Weight (gw) Operation Temperature Noise dB(A) MTBF (hour) CP43A2003 6-13 12.0 1.8 1750 50 5°C - 65°C 23 44,000at 35°C CP43D2001 6-13 12.0 1.7 1650 50 5°C - 60°C 25 30,000at 35°C *Noise Measurement Condition: 25 cm above Pump ( Pump is filled with Pure Water) * Model CP43D2001 is cost down solution. * All readings are typical values.

for CP43A2003) (3 Signals/Rev. for CP43D2001) Specifications Model No. Working Voltage (V) Rated Voltage (V) Max Water Head m-H.O Max Flow Rate ml/min Weight (gw) Operation Temperature Noise dB(A) MTBF (hour) CP43A2003 6-13 12.0 1.8 1750 50 5°C - 65°C 23 44,000at 35°C CP43D2001 6-13 12.0 1.7 1650 50 5°C - 60°C 25 30,000at 35°C *Noise Measurement Condition: 25 cm above Pump ( Pump is filled with Pure Water) * Model CP43D2001 is cost down solution. * All readings are typical values.

HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT. HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY (INCLUDING MERCHANTABILITY). Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty

pecifications shown are subject to change without notice. Specification sheet revised 4/2008 AXOR' 41534001 41534821

Eco spray Normal spray Soft spray From the function is guaranteed. Installation Instructions Install the screen washer between the handshower and the hose. This will protect the handshower from debris in the water line. Depending on local water conditions, you may need to occasionally remove and clean the screen washer. UNDER NO CIRCUMSTANCES SHOULD THE SCREEN WASHER BE PERMANENTLY REMOVED. Using the Uno Handshower Change the spray modes by turning the function ring until the indexing mark is un