The user is prompted with the username and password configured (in the example above, the username/passwordconfigured is admin/admin). On successful login the following Network Summary screen is displayed: PN: 1725-36080-001_J.doc Configuration Guide Initial Setup Before starting, please ensure that the Policy Enforcement Firewall module license is enabled on the Aruba mobility controller. Please contact Aruba Networks for licenses and installation information. On power-up, the user is presented with the startup wizard: Enter System name [Aruba800]: Aruba Enter VLAN 1 interface IP address [172.16.0.254]: Enter VLAN 1 interface subnet mask [255.255.255.0]: Enter IP Default gateway [none]: Enter Switch Role, (master|local) [master]: master Enter Country code (ISO-3166), for supported list: US You have chosen Country code US for United States (yes|no)?: yes Enter Password for admin login (up to 32 chars): admin Re-type Password for admin login: admin Enter Password for enable mode (up to 15 chars): enable Re-type Password for enable mode: enable Do you wish to shutdown all the ports (yes|no)? [no]: no Current choices are: System name: Aruba VLAN 1 interface IP address: 172.16.0.254 VLAN 1 interface subnet mask: 255.255.255.0 IP Default gateway: none Switch Role: master Country code: US Ports shutdown: no If you accept the changes the switch will restart! Type to go back and change answer for any question Do you wish to accept the changes (yes|no)yes PN: 1725-36080-001_J.doc Aruba Mobility Controllers: A200, A800, A2400, A6000 . . . .. <<<<< Welcome to Aruba Wireless Networks - Aruba 800 >>>>> . . . . (Aruba) User: PN: 1725-36080-001_J.doc Configuration Guide Assigning an IP to the Mobility Controller 1. Connect to the switch via the CLI. 2. Login with the configured username and password, admin/admin in this example. 3. Type enable at the > prompt. 4. Type the enable password, enablein this example. 5. Type configure terminal at the #prompt. 6. Create the VLAN for the voice (vlan 25) using the VLAN command: (Aruba) (config) #vlan 25 7. Create the VLAN interface. (Aruba) (config) #interface vlan 25 8. Assign the IP address to the interface. (Aruba) (config-subif)#ip address 10.168.10.2 255.255.255.0 9. Create the loopback interface and assign an IP address to the loopback. For more information about the loopback interface refer to the user guide. (Aruba) (config) #interface loopback (Aruba) (config-loop)#ip address 10.168.10.1 Switch IP Address is Modified. Switch should be rebooted now (Aruba) (config-loop)#! (Aruba) (config) #ip default-gateway 10.168.10.10 10. Assign a physical interface to the VLAN. In this example, the interface connecting to the network is a trunk interface. Configure the mode on the interface to a trunk mode. (Aruba) (config) #interface fastethernet 1/0 (Aruba) (config-if)#trusted (Aruba) (config-if)#no shutdown (Aruba) (config-if)#switchport mode trunk (Aruba) (config-if)#switchport trunk allowed vlan add 10,25 (Aruba) (config-if)#! (Aruba) (config)# 11. Ping the default gateway from the switch’s console. 12. Ping the switch’s IP address from the management station. PN: 1725-36080-001_J.doc Aruba Mobility Controllers: A200, A800, A2400, A6000 Connecting APs Provisioning APs The APs need to be provisioned. The Aruba APs can be provisioned manually or be configured for automatic provisioning. For manual provisioning, use the Web-based AP provisioning Web page. Refer to the AP Provisioning User Guide for instructions on provisioning the AP. The APs can communicate with the controller over a L2 or L3 network. The only requirement is that each AP be assigned an IP address and default gateway using DHCP. PN: 1725-36080-001_J.doc Configuration Guide SSID Configuration CLI command configuration APs can be configured using the CLI or the Web interface. Each AP is identified by a unique location code. The APs can either be configured per location with unique settings using the AP’s unique location code or globally using the wildcard location. “0” is used as the wildcard. Example: ap location 0.0.0 will configure all Aruba APs on the WLAN system. Both the Aruba APs and the Spectralink handsets support the 802.11a and the 802.11b/g radios. To apply the SSID to both bands configure the SSID as follows: configure terminal ap location x.y.z virtual-ap aruba vlan-id 26 opmode wpa2-aes-psk wpa-passphrase thisisthekey dtim-period 3 If the voice network needs to exist only in the 802.11a band , configure the virtual AP under the 802.11a settings on the controller. configure terminal ap location x.y.z phy-type a virtual-ap aruba vlan-id 26 opmode wpa2-aes- psk wpa-passphrase thisisthekey dtim-period 3 If the voice network needs to exist only in the 802.11g band, configure the virtual AP under the 802.11g settings on the controller. configure terminal ap location x.y.z phy-type g virtual-ap aruba vlan-id 26 opmode wpa2-aespsk wpa-passphrase thisisthekey dtim-period 3 To save changes, enter...
)
