valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
Y Y Y Y Y Y Y Y Y Y CR00012683 Switch 2 After the AR770S rebooted, the Port Link/ Activity and Duplex/ Collision LEDs sometimes did not blink in response to activity and collisions, respectively. This issue has been resolved. The router detects the problem and recovers from it, if possible. If it cannot recover from the problem, it generates a log message of severity 6, module SWK, type REST, and subtype FAIL. The log message says “An LED error has been detected, please power-cycle the device. If this message appears again, contact your technical support representative for help. ” - - Y - - - - - - - Version 281- 02 C613- 10482- 00 REV B Features in 281- 01 CR Module Level Description AR400AR7x5AR750S / AR770SRapier iAT-8800AT-8600AT-8700XLAT-8948 / x900-48AT-9900AT-9800 CR00012697 IPsec, ENCO 2 Decrypting a large IPsec ESP packet sometimes caused the router or switch to reboot. This issue has been resolved. Y Y Y Y Y - - - - - CR00012710 Core 2 Soft errors can generate exceptions that would cause the router or switch to reboot. Soft errors are spontaneous changes in the information stored in a digital circuit, caused by physical effects. The router or switch’s handling of such errors has been improved, so that it recovers without rebooting when possible. - - Y - - - - - - - CR00012741 Core, File, Stack 2 The command create config= filename set did not copy the configuration file to all switches in the stack, but only saved the file onto the current switch. This issue has been resolved. - - - Y Y Y Y Y Y - CR00012757 OSPF 2 The router or switch correctly accepted the command add ospf redistribution protocol= static followed by the command set ospf asexternal= on or nssa. However, the command create config did not create a valid configuration file from these commands. If the router or switch used that configuration after a reboot, it gave the error “Redistribution for specified routing protocol - already exists” and did not use the user-defined redistribution definition. This issue has been resolved. The router or switch now correctly saves and uses the user- defined redistribution definition. Y Y Y Y Y Y Y Y Y Y CR00012820 DHCP Snooping, Switch 2 When the switch had two DHCP snooping classifiers applied across all 48 ports, and maxleases was set to 10 or more on each port, the switch rebooted. This issue has been resolved. - - - - - - - Y - - CR00012821 IP Gateway 2 When adding, deleting or updating subnet routes of a more general route, the software and hardware IP route tables sometimes became unsynchronised. The same issue sometimes also occurred when updating ECMP routes. This could cause the router or switch to forward packets to unexpected next hops. This issue has been resolved. - - - Y Y Y Y Y Y Y Version 281- 02 C613- 10482- 00 REV B Features in 281- 01 CR Module Level Description AR400AR7x5AR750S / AR770SRapier iAT-8800AT-8600AT-8700XLAT-8948 / x900-48AT-9900AT-9800 CR00012846 ASYN, Log 2 The following issues occurred with sending log messages to an asynchronous port: ¦ The log messages output on an asynchronous port were corrupt. ¦ When log messages were output to an asynchronous port, that port was ( correctly) locked. However, the port remained locked after the asynchronous log output definition was destroyed, and after the log output's destination was changed from asynchronous to something else. ¦ It was possible for a user to change the log output destination to an asynchronous port while the user was logged into the asynchronous port. This resulted in the user losing access to the command line interface. ¦ It was possible to create a log output definition with an asynchronous port as the destination even when another user was logged into that asynchronous port. This resulted in the other user losing access to the command line interface. ¦ If a user changed the log output destination to an asynchronous port and specified invalid parameters in the command, an error message was displayed but the new output destination was saved anyway. ¦ The set command allowed a user to specify an asynchronous port as the destination without specifying the asynchronous port number. The number defaulted to asyn0, which may not have been the desired port. These issues have been resolved. Y Y Y Y Y Y Y Y Y Y CR00012855 Core 2 If the switch was rebooted at a time when there was a high level of packet traffic between the switch ports and the switch CPU, then during the reboot process it was possible for RAM test errors to occur. This issue has been resolved. - - - - - - - Y Y - Version 281- 02 C613- 10482- 00 REV B Features in 281- 01 CR Module Level Description AR400AR7x5AR750S / AR770SRapier iAT-8800AT-8600AT-8700XLAT-8948 / x900-48AT-9900AT-9800 CR00012868 ENCO 2 Entering the command create enco key= number ip= ? caused the router or switch to reboot. This issue has been resolved. Y Y Y Y Y Y Y Y Y Y CR00012900 IPv6, Switch 2 When an IPv6 accelerator card was installed, IPv6 multicast traffic was flooded to all ...
Questo manuale è adatto anche per i modelli :Apparecchiature di rete - AR44xS (144.62 kb)