valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
indicator 3 Source button Press to select the source input. Rear view English Rear view 1 DC IN Connect the power adapter jack of the receiver. 2 HDMI Connect the HDTV with an OUT HDMI cable. adapter 1 DC IN jack Connect the power 3 IR IN jack Plug in the IR sensor adapter of the transmitter. extender cable. 2 & 3 HDMI IN Connect the HD audio/ adapters video device with the HDMI cables. 4 IR OUT Plug in the IR blaster blaster extender cable. extender jack EN 7 The remote control 1 POWER Press to turn the button transmitter and receiver on/off. 2 INFO Displays on the HDTV button the connection status of the receiver. 3 IR Press to switch the IR button blaster frequency to meet the requirement of the source device. SOURCE Press to switch the button audio/video source inputs connected to the transmitter. The Wireless HD AV Connect gives you a total wireless solution to place your HDTV set or projector anywhere you want.The transmitter can transmit uncompressed video content over 65 feet (19.7 meters) without latency. The receiver can receive signals for viewing on your HDTV. All you need to do is to: • Connect the transmitter to your HD devices. Examples of HD devices are cable/ satellite box, Blu-Ray/HD DVD player, game console or computer. Note • These devices must have an HDMI por t.. • Connect the receiver to your HDTV set. • Control the transmitter with the remote control. 8 EN 4 Installation Connect the transmitter to your HD devices You can connect two audio/video sources to the transmitter at the same time, but only one source can be selected and played. 1 Connect the audio/video source to the transmitter using the supplied HDMI cable. • Connect one end of the HDMI cable to the HDMI IN connector of the transmitter. Note • There are two HDMI IN por ts but only one HDMI cable is supplied. To connect two audio/video sources to the transmitter at the same time, you need an additional HDMI cable. • Connect the other end of the HDMI cable to the HDMI OUT connector of the video source. 2 Connect the supplied power adapter to the transmitter. • Connect one end of the power adapter to the DC IN jack of the transmitter. • Connect the other end of the power adapter to a power outlet. » The power button of the transmitter is lit in solid blue and turns red in standby mode. Connect the receiver to the HDTV set DC 5VHDMI OUTIR IN1 2HDMI IN 1 Connect the receiver with an additional HDMI cable (not supplied): • Connect one end of the HDMI cable to the receiver. • Connect the other end to the HDMI IN connector of your HDTV. 2 Connect the supplied power adapter to the receiver : • Connect one end of the power adapter to the DC IN jack of the receiver. • Connect the other end of the power adapter to a power outlet. » The power button of the receiver is lit in solid blue and turns red in standby mode. English EN 9 Connect the IR blaster and IR sensor extender cables Tip • If you cannot use the remote control of your device, follow the steps in this section to connect the sensor extender cables . 5 Extend and stick the IR sensor extender cable onto the front side of your HDTV. Note • The IR blaster suppor t 47KHz remote signal protocol, while the IR sensor suppor ts 36KHz - 56KHz (NEC, RC5, RC6) remote signal protocol. Connect the infrared blaster or sensor extender cables if necessar y. 1 Plug the IR blaster extender cable into the IR OUT blaster extender jack of the transmitter. 2 Extend and stick the IR blaster extender cable onto the front panel of the HD device. 3 After the IR blaster extender cable is connected to the transmitter, you can control your HD device with the remote control. Make sure that the remote control points to the receiver. 4 If the distance between the receiver and receiver has obstruction (e.g. the receiver is mounted at the back of the HDTV), plug the IR sensor extender cable into the IR IN jack of the receiver. 10 EN Install remote control batteries Caution • Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire. • Risk of decreased batter y life! Never mix different brands or types of batteries. • Risk of product damage! When the remote control is not used for long periods, remove the batteries. AAAAAA 1 Open the batter y compar tment. 2 Inser t two AAA batteries with correct polarity (+/-) as indicated. 3 Close the batter y compar tment. 5 Activate your Wireless HD AV Connect and set up the link Turn on the power of your HDTV DC 5VHDMI OUTIR INHDMIHDMI1 Go to the source menu under the settings menu of your HDTV. 2 Select the HDMI input to which the receiver is connected. On screen display on HDTV On screen Mode and status display Standby mode: it is a power- saving mode ..... Star t up in progress: It takes 1520 seconds. x and .... Searching available channels: It occurs when the link cannot establish over 80 seconds after initialization. HDMI On mode with unrecognized CH1 video format HDMI On mode but without input CH1 from the source device HDMI...