valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
1a fig. 1b fig. 2a fig. 2b SBC RU 885 R DC 9V XP SBC LI 805 24-06-2002 09:06 Pagina 2 XP SBC LI 805 24-06-2002 09:06 Pagina 3 2 Helpline Belgie & Luxemburg Belgien & Luxemburg Belgique & Luxembourg 070 - 222303 Danmark 808 82814 Deutschland 0180 - 53 56 767 Espana 902 - 11 33 84 France 08 25 88 97 89 00800 3122 1280 Ireland 01 - 7640292 Italia 800 820026 Nederland 0900 - 8406 Norge 2274 8250 Osterreich 0810 - 001203 Portugal 021 416 3063 die Schweiz/ Suisse/ Svizzera 0844 800 544 Suomi 09 615 80 250 Sverige 08 - 598 522 50 United Kingdom 0208 - 665 - 6350 European regulations This product has been designed, tested and manufactured according to the European R&TTE directive 1999/5/EC. Following this Directive, this product can be brought into service in the following states: SBC LI 800/00 SBC LI 800/05 R&TTE Directive 1999/5/EC R&TTE Directive 1999/5/EC BE . DK . GR . ES . FR . IRE . IT . LU . NL . AT . PT . FI . SE . UK . NO. DE . CH . BE . DK . GR . ES . FR . IRE . IT . LU . NL . AT . PT . FI . SE . UK . NO. DE . CH . 0682 ENGLISH4 XP SBC LI 805 24-06-2002 09:06 Pagina 4 Receiver SBC LI 805 Receiver The Philips SBC LI 805 receiver can be used as receiver for the SBC RU 885 R(adio) F(requency) remote control as well as additional receiver for the SBC LI 800 Remote Control extender set. When used in conjunction with the RU 885 you can operate most IR driven equipment (e.g. Hi-Fi sets, VCRs, Sat-receivers, etc.) from anywhere in your house without actually seeing the equipment or aiming the remote control at it. For operation with the LI 800 extender set, see the User Guide of the set. The RU 885 is able to send RF (radio frequency) signals that go through walls or, if your equipment is located in a cabinet, through the cabinet door. When receiving a signal from the RU 885, the receiver re-conver ts the RF-signal to a propriate IR signal and sends it to the equipment you wish to operate. In case you wish to control equipment in different rooms you can extend your equipment with more LI 805 receivers. IR extension cord The extension cord can be connected if the receiver is located in a cabinet or if you do not want to place the unit in front of your equipment. The cord has three IR lights that allow you to operate three devices simultaneously. Adapter For connecting the receiver to the mains supply. To ensure you get the best performance from your receiver please read this manual carefully. Important information Read these instructions. All operating instructions and safety precautions should be read before using the receiver. Safety precautions • Check if the voltage indicated on the type plate of the adapter corresponds to the local mains voltage before connecting to the mains power supply. • The receiver is powered once it is connected to a 230-240 VAC mains supply. Disconnect the receiver from the mains supply when not in use. • Do not use the receiver in moist places or close to water. • Do not expose the receiver to extreme heat or light. • When cleaning the receiver, first disconnect from the mains supply. Rub it with a dry or slightly moist towel, never use excessive amounts of water on the unit. Contents Helpline 2 General 4 Important information 4 Installation 5 Operation 6 Troubleshooting 7 Installation Receiver - fig. 1b 1 Place the receiver in front of the equipment you want to control. The receiver should be facing the equipment with its front window, or with its back; the receiver is able to transmit IR signals through its dark rear side. 2 Connect the adapter supplied to the receiver and connect the adapter to the mains supply (230-240 VAC). > The green light will light up in the window on the front. Extension cord - fig. 2 1 Connect the extension cord to the receiver and position the receiver beside or behind the equipment you want to control. 2 Remove the adhesive tape from the IR light(s) and affix the IR light(s) on the IR sensor(s) of the equipment you wish to control. Notes: – For the location of the IR receiver(s) on your equipment, check the appropriate manuals. – If the location of the IR receiver(s) is not exactly known you can place the IR lights 5-10 cm away from the front of the equipment you wish to control. ENGLISH 5 R DC 9V R DC 9V TUNER CD DVD XP SBC LI 805 24-06-2002 09:06 Pagina 5 XP SBC LI 805 24-06-2002 09:06 Pagina 6 6 ENGLISH Operation Operation with RU 885 RF remote control 1 Make sure the RF functionality of the RU 885 is enabled. 2 Select the equipment you wish to operate. 3 Point the remote control in the direction of the receiver and press the required function button. > The receiver will confirm reception by the flashing of the red light in the window on the front and your equipment will respond. • For detailed operating instructions see the RU 885 User Guide. Operation in the SBC LI 800 Remote Control extender set • Once installed, the receiver can be used as additional receiver in the SBC LI 800 Remote Control extender set. • For detailed operating instructions s...