valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Double-click on a link in the table of contents or index to navigate directly to where the topic is described in the manual. •A button to access the full NETGEAR, Inc. online knowledge base for the product model. •Links to PDF versions of the full manual and individual chapters. How to Print this Manual •Printing a Page in the HTML View. Each page in the HTML version of the manual is dedicated to a major topic. Use the Print button on the browser toolbar to print the page contents. •Printing a Chapter. Use the PDF of This Chapter link at the top left of any page. Tip: If your printer supports printing two pages on a single sheet of paper, you can save paper and printer ink by selecting this feature. •Printing the Full Manual. Use the Complete PDF Manual link at the top left of any page. Tip: If your printer supports printing two pages on a single sheet of paper, you can save paper and printer ink by selecting this feature. Chapter 2 Introduction Key Features •RangeMax™ Multi-In, Multi-Out (MIMO) technology •802.11g wireless networking, with the ability to operate in 802.11g-only, 802.11b only, or 802.11b+g modes. •Easy, Web-based setup for installation and management. •Login capability. •Front panel LEDs for easy monitoring of status and activity. •Flash memory for firmware upgrades. RangeMax™ Multi-In, Multi-Out (MIMO) Technology 802.11g Wireless Networking •802.11g wireless networking at up to 108 Mbps. •802.11g wireless networking, with the ability to operate in 802.11g-only, 802.11b-only, or 802.11g and b modes, providing backwards compatibility with 802.11b devices or dedicating the wireless network to the higher bandwidth 802.11g devices. •64-bit and 128-bit WEP encryption security. •WEP keys can be generated manually or by passphrase. •WPA-PSK support. Support for Wi-Fi Protected Access (WPA) data encryption which provides strong data encryption and authentication based on a pre-shared key. •Wireless access can be restricted by MAC address. •Wireless network name broadcast can be turned off so that only devices that have the network name (SSID) can connect. Autosensing Ethernet Connections with Auto Uplink Compatible and Related NETGEAR Products •RangeMax Wireless USB 2.0 Adapter (WPN111) •RangeMax Wireless PCI Adapter (WPN311) •RangeMax Wireless PC Card (WPN511) Package Contents •NETGEAR RangeMax™ Wireless Access Point WPN802. •AC power adapter. •Vertical stand. •Straight through Category 5 (CAT5) Ethernet cable. •Resource CD for the NETGEAR WPN802 RangeMax™ Wireless Access Point (240-10213-01), including: •WPN802 Quick Installation Guide. •Warranty and Support Information Card. The Front Panel Status Lights The Rear Panel •AC power adapter outlet. •Ethernet 10/100 Mbps port for connecting the access point to the network. •Factory Default Reset push button for Using the Reset Button to Restore Factory Default Settings. Chapter 3 Basic Installation and Configuration Default Factory Settings System Requirements •A 10/100 Mbps Local Area Network device such as a hub, router, or switch. •The Category 5 UTP straight through Ethernet cable with RJ-45 connector included in the package, or one like it. •A 100-240 V, 50-60 HZ AC power source. •A Web browser for configuration such as Microsoft Internet Explorer 6.0 or above, or Netscape Navigator 4.78 or above. •At least one computer with the TCP/IP protocol installed. •802.11b or 802.11b-compliant devices, such as the NETGEAR RangeMax Wireless PCI Adapter (WPN311). Prepare to Install Your Wireless Access Point •Observe the wireless placement and range guidelines in “Observe Performance, Placement, and Range Guidelines” on page 4-1. •For Cable Modem Service: When you perform the wireless access point setup steps be sure to use the computer you first registered with your cable ISP. •For DSL Service: You may need information such as the DSL login name/e-mail address and password in order to complete the wireless access point setup. •Familiarize yourself with the contents of the Resource CD for the NETGEAR WPN802 RangeMax™ Wireless Access Point (240-10213-01), especially this manual and the animated tutorials for configuring networking on PCs. First, Connect the Wireless Access Point to Your Computer •Power: The power light should be lit. If the power light is not lit, check the connections and check to see if the power outlet is controlled by a wall switch that is turned off. •Test: The test light blinks when the WPN802 is first turned on. • WLAN: The wireless light should be lit. •Ethernet: The Ethernet (LAN) light should be lit (amber for a 10 Mbps connection and green for a 100 Mbps connection). If not, make sure the Ethernet cable is securely attached at both ends. Then, Configure the Basic Settings •Access Point Name: The unique NetBIOS name. The default Access Point Name is located on the bottom label of the WPN802. You may modify the default name with a unique name up to 15 characters long. •IP Address: By default, the Access Point is set to be a DHCP (D...
Questo manuale è adatto anche per i modelli :Apparecchiature di rete - WPN802v1 (1.03 mb)