For instructions on installing and verifying the Windows network driver, refer to “Install the Windows Network Driver” on the other side of this guide. These three easy steps are provided in this guide for installing your Model FA310TX Network Card: 1. Verify Package Contents 2. Install the Network Card 3. Connect the Network Cables As a last step, be sure to register your NETGEAR product. Note: If you are using other network operating systems: Insert the Drivers and Diagnostics Disk in Drive A, type the command A:\HELP, press [Enter] to execute the program, press [Enter] again to pass the opening screen, select the name of the operating system, press [Enter], and then follow the instructions on the screen. Model FA310TX Network Card Installation Guide Verify Package Contents Verify Package Contents Unpack the contents of the package and make sure that you have everything. Model FA310TX Network Card Installation guide Drivers and Diagnostics Disk Category 5 10/100 Mbps UTP cable (provided with Model FA310TXC Network Card) 9014FA Verify PC Requirements The instructions given in this guide are for using the NETGEAR™ Model FA310TX Network Card in a PC that has a Microsoft® Windows operating system. You must have a PC with a PCI expansion slot that has bus mastering capability. Model FA310TX Network Card Installation Guide Install the Network Card Install the Network Card Note: Touch a grounded metal object to free yourself of static electricity before you handle the network card. 1. Turn the power off and unplug the power cord from your computer. 2. Remove the PC cover. 3. Choose an available PCI slot (PCI slots are the shorter slots) and remove the corresponding back plate from the PC chassis. 4. Insert the network card into the PCI expansion slot. Note: To avoid damaging any components on the network card, handle it by the edges, using your thumbs to push it securely into the PCI slot. Make sure the network card is fully inserted into the slot to prevent the PC operating system from freezing at startup. 5. Fasten the network card to the rear of the computer chassis by tightening the screw that is on the PC. 6. Replace the PC cover and reconnect the power cord to the PC. Network card Back plate removed 7983FB Model FA310TX Network Card Installation Guide Connect the Network Cables Connect the Network Cables Using the appropriate UTP cable, connect any port on a network hub to the port on the network card. Note: One of the ports on NETGEAR hubs is switchable between Normal (MDI-X) and Uplink (MDI) with a Normal/Uplink push button. If you are using this switchable port on a NETGEAR hub to connect to a PC or the network card, make sure the Normal/Uplink push button is set to Normal. 7995FB RJ-45 connector RJ-45 connector PC with network card installed Power adapter PC with network card installed Printer (optional) *Use the cables provided or any Category 5 UTP cable. Maximum length = 100 meters (300 feet) Category 5 10/100 Mbps UTP cables* Hub Model FA310TX Network Card Installation Guide Install the Windows 95 Network Driver Install the Windows 95 Network Driver This guide provides instructions for installing the Windows Network Driver. The steps given are for users of Windows 95. However, because all versions of Windows 95 might not respond the same, windows that are different from those shown in these instructions might open but prompt you for the same information, or windows might open in a different order than shown in these instructions. If you are using Windows 98, read these instructions thoroughly for an overview of the steps that are necessary for the installation of the software driver. Follow the instructions given by the Windows 98 Installation Wizard to install the driver. Note: You must install the network card (instructions on other side of this guide) before installing the network driver. You need to have the Windows CD-ROM and the FA310TX Drivers and Diagnostics Disk ready to use in the installation process. If you have not yet named your PC and your network, before you proceed with the installation steps, decide on a name for your network and for each PC. When the “Network” window opens, it prompts you to “... provide computer and workgroup names....” Click on “OK.” The second “Network” window opens and prompts you for the names. Enter a name (a different one- word name for each computer) in the “Computer name” entry field; enter a workgroup name (the name of your entire network) in the “Workgroup” entry field. Click on “OK” or “Close.” Note: If the “Insert Disk” window opens and the “Please insert the disk labeled Windows...” message appears at any time during the installation process, insert the Windows CD-ROM in Drive D (the CD-ROM drive) and click on “OK.” Then follow the next step in the instructions. 1. Turn on the power to the computer and start Windows 95. The new hardware is found, and the driver is automatically loaded. Model FA310TX Network Card Installation Guide 2. New Hardware Fo...

Questo manuale è adatto anche per i modelli :
Apparecchiature di rete - FA310TX (498.78 kb)