valutazioni - , GPA:
(
)
)
Produttore : Woodstock
File Size : 2.99 mb
File Nome : w1688_m.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
Immediately replace a damaged extension cord. Amp Rating Length and Gauge 25ft 50ft 100ft 0-6 #18 #16 #16 7-10 #18 #16 #14 11-12 #16 #16 #14 13-16 #14 #12 #12 17-20 #12 #12 #10 21-30 #10 #10 No 17. Keep proper footing and balance at all times. 18. Do not leave machine unattended. Wait until it comes to a complete stop before leaving the area. 19. Perform machine maintenance and care. Follow lubrication and accessory attachment instructions in the manual. 20. Keep machine away from open flame. Operating machines near pilot lights and/or open flames creates a high risk if dust is dis- Always wear safety glasses or goggles when persed in the area. Dust particles and an operating equipment. Operating this equip- ignition source may cause an explosion. Do ment creates the potential for flying debris not operate the machine in high-risk areas, that can cause eye injury. Everyday glasses including but not limited to, those men- or reading glasses only have impact resistant tioned above. lenses, they are not safety glasses. Be cer 21. If at any time you are experiencing diffi-tain the safety glasses you wear meet the culties performing the intended operation, appropriate standards of the American stop using the machine! Then contact our National Standards Institute (ANSI). service department or ask a qualified expert how the operation should be performed. 22. Habits—good and bad—are hard to break. Develop good habits in your shop and safety will become second-nature to you. SAFETY -5 Additional Safety Instructions for Edge Sanders SAFETY INSTRUCTION MANUAL MODEL W1688 EDGE SANDER Phone: 1-360-734-3482 • On-Line Technical Support: shopfox.biz COPYRIGHT © SEPTEMBER, 2002 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in Taiwan Read and understand this Use this and other machinery with caution entire instruction manual and respect, and always consider safety before using this machine. first, as it applies to your individual working Serious personal injury conditions. Remember, no list of safety may occur if safety and guidelines can be complete and every shop operational information is environment is different. Failure to follow not understood and folguidelines can result in serious personal lowed. Do not risk your injury, damage to equipment and/or poor safety by not reading! work results. 1. Be aware of sanding belt rotation when sanding. Always brace workpiece against the rotation of the sanding spindle. 2. Keep fingertips away from the moving sanding belt. 3. Never use excessive force when sanding. Doing this greatly increases the chances of personal injury and motor overload. 4. Always feed the work against the direction of rotation. 5. Even if you have a reliable method of dust collection, use a dust mask or respirator when sanding, as well as eye and ear protection. 6. If there is any doubt as to the stability or integrity of the material to be sanded, do not sand it. 7. Do not operate sander with a damaged or badly worn sanding belt or rollers. 8. Sanding dust from some woods may be toxic or cause an allergic reaction. Be sure to wear an appropriate respirator when working around sawdust. Make sure there is adequate ventilation or a constant source of fresh air. The sawdust from some species of wood can be toxic to some people. Be sure to research the dangers of the specific species of wood you are working with. -6 Avoiding Potential Injuries Back Stop Figure 1. DO NOT hold wood away from the backstop, and keep your fingers away from the belt. Back Stop Figure 2. ALWAYS use the back stop, and keepyour fingers away from the belt. Figure 3. DO NOT sand wood with your fingersclose to the idler roller and belt. Figure 4. ALWAYS keep your fingers away fromthe idler roller and the belt. Figure 5. DO NOT sand wood with sharp cornersat the leading-edge of the sanding operation. Thebelt can grab and throw the wood. Figure 6. ALWAYS sand wood with sharp cornersat the trailing-edge of the sanding operation. SAFETY -7 ELECTRICAL REQUIREMENTS Grounding Any electrical outlet and circuit that you plug your machine into must be grounded. Serious injury and/or fire may occur if this warning is ignored! Ground this machine! The electrical cord supplied with the Model W1688 does not come with a 220 volt plug. Use a plug with a ground pin as shown in Figure 7. If your receptacle does not accommodate a NEMA 6-15 plug with a ground pin, have the receptacle replaced by a qualified electrician or have an appropriate adapter installed and grounded properly. NOTICE Make sure when using an adapter, the adapter is grounded. Remember, an adapter with a grounding wire does not guarantee the machine will be grounded. A ground source must always be verified in the electrical circuit within the wall or conduit. 6-15P 6-15R Figure 7. NEMA-style 6-15 plug and receptacle. ELECTRICAL 220V Operation The SHOP FOX® W1688 ...