valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Step3: On the top of the WATER TRAP is an arrow. Attach the BRASS AIR SUPPLY VALVE to the NIPPLE CONNECTOR that the arrow is facing away from. Step4: Attach the MALE/FEMALE ADAPTER to the BRASS AIR SUPPLY VALVE. Page #6 -- SKU 34202 Sand Control Valve Refer to Figure 3. Step1: Get out the TANK (#1), the SAND CONTROL VALVE (#18B), two NIPPLE CONNECTORS (#16), and the SAND OUTLET MANIFOLD (#22). Nipple Connector (#16) Sand Control CONNECTORS to the bottom of the (#1) Step2: Attach one of the NIPPLE Tank Valve (#18B) TANK (#1). Step3: Attach the SAND CONTROL VALVE to the other end of the NIPPLE CONNECTOR. Sand Outlet Manifold Step4: Attach the other NIPPLE CONNECTOR (#22) to the other end of the SAND CONTROL VALVE. Step5: Attach the other end of the NIPPLE CONNECTOR to the side hole of the SAND OUTLET MANIFOLD. Figure 3 — Sand Control Valve Assembly Nozzle Shut Off Valve Refer to Figure 4. Steel Shut Step1: Get out the Hose Adaptor HOSE ADAPTER (#25), the STEEL SHUT OFF VALVE Nipple Gasket (#18C), a NIPPLE (#26) Connector CONNECTOR (#16), (#16) the GASKET (#26), Nozzle Cap the desired size Nut Nozzle NOZZLE (#27A-D), (#28) (#27A-D) and the NOZZLE CAP NUT (#28). Figure 4 — Nozzle Shut Off Valve Step2: Put the front of the NOZZLE through the NOZZLE CAP NUT. Step3: Attach the NOZZLE CAP NUT to the NIPPLE CONNECTOR with the GASKET between the NIPPLE CONNECTOR and the NOZZLE. The flat end of the GASKET should face the NIPPLE CONNECTOR. Step4: Attach the other end of the NIPPLE CONNECTOR to one side of the STEEL SHUT OFF VALVE. Page #7 -- SKU 34202 (#25) Off Valve (#18C) Step5:Attach the HOSE ADAPTER to the other end of the STEEL SHUT OFF VALVE. Sand Control Valve/ Nozzle Shut Off Valve Refer to Figure 5. Sand Hose Nozzle Shut Off Valve Assembly Hose Clamp (#23) Sand Control Valve Assembly Figure 5 — Sand Control Valve / Shut Off Valve Assembly Step1: Get out the Sand Control Valve & Nozzle Shut Off Valve Assemblies, the SAND HOSE (#24), and the two HOSE CLAMPS (#23). Step2: Slide the HOSE CLAMPS over either side of the SAND HOSE. Do not tighten yet. Step3: Slide one end of the SAND HOSE onto the Nozzle Shut Off Valve Assembly’s HOSE ADAPTER (#25). Tighten the HOSE CLAMP very securely. Step4: Slide the other end of the SAND HOSE onto the Sand Control Valve Assembly’s SAND OUTLET MANIFOLD (#22). Tighten the HOSE CLAMP very securely. Page #8 -- SKU 34202 Top Assembly Refer to Figure 6. Tank (#1) Nipple Connector (#16) Nipple Connector (#16) Air Hose (#21) Gasket (#11) Air Cap (#12) Joint Pipe (#13) Figure 6 — Top Assembly Step1: Get the Intake Valve Assembly, the Water Trap Assembly, the Tank Assembly, the TANK CAP (#12), the O-RING (#11), and the AIR HOSE (#21). Step2: Attach the Water Trap Assembly’s NIPPLE CONNECTOR (#16) to the upper side INTAKE MANIFOLD (#14). Step3: Attach the JOINT PIPE (#13) to the upper side port of the TANK (#1). Step4: Put the O-RING into the fill port of the TANK. Step5: Screw the TANK CAP onto the fill port of the TANK. Step6: Attach the female end of the AIR HOSE to the BRASS THROTTLING VALVE’S (#18A) NIPPLE CONNECTOR (#16). Step7: Attach the male end of the AIR HOSE to the SAND OUTLET MANIFOLD(#22), underneath the TANK. Page #9 -- SKU 34202 Handle Bars Refer to Figure 7. Handle Grip (#7) Handle Bar (#6) Screw (#8) Washer (#31) Nut (#9) Figure 7 — Handle Bar Assembly Step1: Get out the two HANDLE BARS (#6), the two HANDLE GRIPS (#5), the four SCREWS (#8), four NUTS (#9), and four WASHERS (#31). Step2: Slide the HANDLE GRIPS onto the HANDLE BARS. Step3: Attach both HANDLE BARS to the TANK (#1) using the four SCREWS, NUTS, and WASHERS. The HANDLE BARS must curve back and the holes in their bottoms must be parallel to each other. The WASHERS go between the NUTS and the TANK. Right Handle (#6-R) Left Handle (#6-L) Page #10 -- SKU 34202 REV 01/01 Wheels and Foot See Figure 8. 5 3 2 4 3 3 2 Figure 8 - Wheel and Foot Attachment Step 1: Get out the two WHEELS (#2), the three COTTER PINS (#3), the FOOT (#4) and the AXLE (#5). Step 2: Attach the FOOT to the TANK (#1) using one of the COTTER PINS. Step 3: Attach one of the WHEELS to the AXLE using one of the COTTER PINS. Step 4: Slide the AXLE through the hole in the bottom of the two HANDLE BARS (#6). Step 5: Attach the other WHEEL to the AXLE using the remaining COTTER PINS. Safety Valve Step 1: Screw the SAFETY VALVE (#10) into the hole in the top of the TANK (#1). Page #11 -- SKU 34202 OPERATIONS Loading Abrasives Step 1: Check to insure the abrasives are dry and clean so that they do not clog the unit. Warning! Always wear your hood, dust mask, and heavy-duty canvas Step 2: Close the AIR SUPPLY VALVE (#18) by turning it to gloves when operating the the horizontal position. Sand Blaster. Step 3: Open the NOZZLE SHUT OFF VALVE (#18C) by turning it to the vertical position. Step 4: Make sure the PRESSURE GAUGE (#15) reads “0”. Step 5: Remove the TANK CAP (#12). Note: Place your Air Compressor in Step 6: Using the FUNNEL (#29), pour the selected a...