valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
(See Figure C, and Assy. Diagram.) BRAKE PIN (#18) SIDE HANDLE (#20) WOOL COVER (#45) BRUSH CAP (#40) CARBON BRUSH (#41) BRUSH HOLDER (#42) VARIABLE SWITCH (#31) BACK HANDLE (#39) POWER CORD (#36) FIGURE C OPERATING INSTRUCTIONS NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 12 of this manual. SKU 46507 PAGE 8 To Attach The Rubber Backing Plate And Sandpaper: To Attach The Rubber Backing Plate And Sandpaper: . Caution: Prior to installing the Rubber Backing Plate (part #46), make sure the Polisher/Sander is disconnected from its electrical power source. 2. Rest the tool on a flat surface. Depress the Brake Pin (#18) to keep the Spindle (#3) from turning. 3. Screw the Rubber Backing Plate (46) onto the threaded end of the Spindle (#3) until it is snug. (See diagram below) 4. Ahere Sandpaper Disc (not included) evenly across the Rubber Backing Plate. The Rubber Backing Plate has a self-sticking backing, so be sure only to use Sandpaper Discs with a self-sticking material. Press Sandpaper Disc firmly onto pad. When finished, release pressure on the Brake Pin (#18). 5. When finished sanding, peel the Sandpaper Disc away from the Plate. BRAKE PIN (#18) RUBBER BACKING PLATE (#46) SPINDLE (#3) SANDPAPER DISC SKU 46507 PAGE 7 1. Caution: Check to make sure the Switch (part #33) is in its “OFF” position before plugging the Power Cord (part #36) into a 110-120 Volt, grounded, electrical power outlet. (See Figures B, C, and Assy. Diagram.) 2. Make sure to use both hands to firmly grip the Polisher/Sander by its Side Handle (part #20) and Back Handle (part #39). (See Figures B, C, and Assy. Diagram.) 3. To turn on the Polisher/Sander, squeeze the Switch (part #33). To turn off the Polisher/Sander, release pressure on the Switch. NOTE: For automatic, continuous running, squeeze the Switch while, at the same time, depressing the Switch Lock. This locks the Switch in its “ON” position. To turn off the Polisher/Sander, squeeze and quickly release pressure on the Switch. This unlocks the Switch, and allows the Polisher/Sander to automatically turn off. (See Figures B, C, and Assy. Diagram.) 4. Allow the Polisher/Sander to spin up to full speed before pressing it onto the workpiece. (See Figures B, C, and Assy. Diagram.) 5. NOTE: The Polisher/Sander can be operated at different speeds (from 1,000 RPM to up to 3,000 RPM), depending on the material of the workpiece. To change speeds, make sure the Polisher/Sander is off. Then, select the desired speed, using the Variable Switch (part #31). (See Figures B, C, and Assy. Diagram.) 6. Do not force the Polisher/Sander onto the workpiece. Apply moderate pressure, allowing the Polisher/Sander to do the work without being forced. (See Figures B, C, and Assy. Diagram.) 7. Move the Polisher/Sander along the workpiece in small, circular, patterns. (See Figures B, C, and Assy. Diagram.) 8. When finished, turn off the Polisher/Sander and allow the Polishing Disc or the Rubber Backing Plate to spin down and stop on their own. Do not press against the disc to stop them. (See Figures B, C, and Assy. Diagram.) INSPECTION, MAINTENANCE, AND CLEANING 1. Caution: Always disconnect the Polisher/Sander from its electrical power supply source before performing any inspection, maintenance, or cleaning. 2. Before each use, inspect the general condition of the Polisher/Sander. Inspect switch, power plug and cord assembly, and extension cord (if used) for damage. Check for loose screws, misalignment, binding of moving parts, broken, cracked, or improper mounting of the Polishing Disc or the Rubber Backing Plate, broken SKU 46507 PAGE 9 parts and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, turn off the Polisher/Sander immediately and have the problem corrected before further use. parts and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, turn off the Polisher/Sander immediately and have the problem corrected before further use. 3. The Polisher/Sander features two Carbon Brushes (part #41) which, periodically, should be examined for wear. The Carbon Brushes are located on each side of the Plastic Housing (part #29). To inspect or replace the Carbon Brushes, use a small standard screwdriver to remove the Brush Cap (part #40). Examine the concave surface of the Carbon Brushes. The surface should be smooth and clean. If there are large scratch marks in the Brushes, or parts of the Brushes have broken off, replace both Brushes immediately with approved replacement Brushes from Harbor Freight Tools. To reinstall the Brushes, insert them into the two Brush Holders (part #42). Turn the Brushes vertically so they will fit into the Brush Holders. Then, replace the Brush Caps. (See Figures B, C, and Assy. Diagram.) 4. Do not use solvents to wipe off the Polisher/Sander, as damage may result. If necessary, wipe with a damp cloth. You may use a mild detergent. 5. Do not int...