valutazioni - 5, GPA: 4.2
(
)
)
|
Facilità d'uso
If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. Table 1: Minimum gage for cord Ampere Rating Volts Total length of cord in feet 120 V 25 ft. 50 ft. 100 ft. 150 ft. More Than Not More Than AWG 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended GROUNDING INSTRUCTIONS This tool should be grounded while in use to protect the operator from electric shock. The tool is equipped with a three-conductor cord and three-prong grounding type plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Never connect the green (or green and yellow) wire to a live terminal. Your unit is for use on 120 volts and has a plug that looks like Fig. “A”. An adapter Fig. “B” and “C” is available for connecting Fig. “A” type plugs to two-prong receptacles. The green-colored rigid ear, lug, etc., extending from the adapter must be connected to a permanent ground, such as a properly grounded outlet box. Grounding MeansCover of Grounded Outlet Box Adapter Grounding Blade Fig. A Fig. B Fig. C An adapter Fig. “B” and “C” is available for connecting Fig. “A” type plugs to two-prong receptacles. The green-colored rigid ear, lug, etc., extending from the adapter must be connected to a permanent ground, such as a properly grounded outlet box. Grounding MeansCover of Grounded Outlet Box Adapter Grounding Blade Fig. A Fig. B Fig. C USB006-2SPECIFIC SAFETY RULES DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to grinder safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 2. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. 3. Always use safety glasses or goggles. Ordinary eye or sun glasses are NOT safety glasses. 4. Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. Run the tool at no load for about a minute, holding tool away from others. If wheel is flawed, it will likely separate during this test. 5. Hold the tool firmly. 6. Keep hands away from rotating parts. 7. Make sure the wheel is not contacting the workpiece before the switch is turned on. 8. Before using the tool on an actual work- piece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel. 9. Watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials. 10. Do not leave the tool running. Operate the tool only when hand-held. 11. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. 12. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 13. Do not use water or grinding lubricant. 14. Do not use this tool as cutter. 15. ALWAYS wear proper apparel including long sleeve shirts, leather gloves and shop aprons to protect skin from contact with hot grindings. 16. Use of this tool to grind or sand some products, paints and wood could expose user to dust containing hazardous substances. Use appropriate respiratory protection. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. FUNCTIONAL FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 003487 Switch action CAUTION: • Before plugging in the tool, always check to see that the tool is switched off. • Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, move the switch lever to the “ON” position. To stop the tool, move the switch lever to the “OFF” position. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003492 Installing or removing wheel point Loosen the collet nut and insert the wheel point into the collet nut. Use the smaller wrench to hold the spindle and the larger one to tighten the collet nut securely. 1 1. Switch lever 1 2 3 1. Wrench 17 2. Wrench 10 3. Collet nut 10 mm (3/8”) Max. 003494 The wheel point should not be mounted more than 10 mm (3/ 8”) from the collet nut. Exceeding this distance could cause vibration or a broken shaft. To remove the wheel point, follow the installation procedure in reverse. CAUTION: • A 1/4” collet cone is provided as standard equipment. Us...