valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
Unplug tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire cup brush onto spindle and tighten with supplied wrench. When using brush, avoid applying too much pressure which causes over bending of wires, leading to premature breakage. 1 1. Wire cup brush 10 Operation with wire wheel brush (optional accessory) CAUTION: • Check operation of wire wheel brush by running tool with no load, insuring that no one is in front of or in line with the wire wheel brush. • Do not use wire wheel brush that is damaged, or which is out of balance. Use of damaged wire wheel brush could increase potential for injury from contact with broken wires. • ALWAYS use guard with wire wheel brushes, assuring diameter of wheel fits inside guard. Wheel can shatter during use and guard helps to reduce chances of personal injury. Unplug tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wrenches. When using wire wheel brush, avoid applying too much pressure which causes over bending of wires, leading to premature breakage. Operation with abrasive cut-off wheel (optional accessory) WARNING: • When using an abrasive cut-off wheel, be sure to use only the special wheel guard designed for use with cutoff wheels. • NEVER use cut-off wheel for side grinding. During cutting operations, never change the angle of the wheel. Placing side pressure on the cut-off wheel (as in grinding) will cause the wheel to crack and break, causing serious personal injury. 1. Wire wheel brush 1 001228 1. Lock nut 2. Abrasive cut-off wheel 3. Inner flange 4. Wheel guard for cut-off wheel 001116 1 3 2 4 MAINTENANC E 001161 2 1 1. Exhaust vent 2. Inhalation vent 001145 1 1. Limit mark 001148 1 2 1. Brush holder cap 2. Screwdriver ACCESSORIES CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. The tool and its air vents have to be kept clean. Regularly clean the tool’s air vents or whenever the vents start to become obstructed. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. • Your tool is supplied with a guard for use with a depressed center grinding wheel, multi-disc, flex wheel and wire wheel brush. A cut-off wheel can also be used with an optional guard. If you decide to use your Makita grinder with approved accessories which you purchase from your Makita distributor or factory service center, be sure to obtain and use all necessary fasteners and guards as recommended in this manual. Your failure to do so could result in personal injury to you and others. from your Makita distributor or factory service center, be sure to obtain and use all necessary fasteners and guards as recommended in this manual. Your failure to do so could result in personal injury to you and others. 1 2 2 8 2 12 13 3 3 9 11 3 4 6 10 14 5 7 5 5 9526PBH 9527PB 9528PB 1 Grip 36 2 Wheel guard 3 Inner flange 35 Inner flange 45 Inner flange 45 4 Depressed center grinding wheel/Multi-disc 5 Lock nut 10-35 Lock nut 5/8-45 Lock nut 5/8-45 6 Plastic pad N/A N/A 7 Flex wheel N/A N/A 8 Rubber pad 76 Rubber pad 100 Rubber pad 115 9 Abrasive disc 10 Sanding lock nut 10-30 Sanding lock nut 5/8-48 Sanding lock nut 5/8-48 11 Wire wheel brush 12 Wire cup brush 13 Wheel guard (For cut-off wheel) 14 Cut-off wheel -Lock nut wrench 20 Lock nut wrench 28 Lock nut wrench 28 Memo Memo Memo Memo MAKITA LIMITED ONE YEAR WARRANTY MAKITA LIMITED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge. This Warranty does not apply: • where normal maintenance is required, • repairs have been made or attempted by othe...
Questo manuale è adatto anche per i modelli :Rettificatrici - 9526PBH (208.93 kb)
Rettificatrici - 9528PB (208.93 kb)