valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Undetectable damage to guard or mounting hub may result. MOUNTING CUTTING WHEELS 1. Remove Soft Mount (F). 2. Install wheel backing flange, aligning flats on spindle (O) with flats on backing flange (R). 3. Place the wheel on the backing flange, centering the wheel on the backing flange pilot. 4. Install the clamp nut, ensuring that the wheel remains centered on the backing flange. 5. Depress the spindle lock button and tighten clamp nut with wrench. 6. Reverse the above procedure to remove the wheel. USING CUTTING WHEELS 1. Allow tool to reach full speed before touching tool to work surface. 2. Apply minimum pressure to work surface, allowing tool to operate at high speed. 3. Once you begin a cut, maintain the angle of the cutting wheel to the work surface. This will keep you from bending the wheel which could result in wheel breakage and injury. 4. Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before setting it down. MAINTENANCE Cleaning WARNING: Blowing dust and grit out of the motor housing using clean, dry compressed air is a necessary regular maintenance procedure. Dust and grit containing metal particles often accumulate on interior surfaces and could create an electrical shock or electrocution if not frequently cleaned out. ALWAYS WEAR SAFETY GLASSES. CAUTION: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. Use a clean, dry rag only. Lubrication DEWALT tools are properly lubricated at the factory and are ready for use. F O R I 399080-02 rev 11/15/02 10:13 AM Page 15 399080-02 rev 11/15/02 10:13 AM Page 1 6 English Repairs To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel. Always use identical replacement parts. Motor Brushes When brushes become worn, the tool will automatically stop, preventing damage to the motor. Brush replacement should be performed by DEWALT authorized service centers or other qualified service personnel. Qualified service personnel should follow the procedures below when replacing motor brushes. Turn off and unplug tool before making any adjustments or removing or installing accessories. Before reconnecting the tool, depress and release the trigger switch to ensure that the tool is off. 1. Remove the brush doors located on the sides of motor housing. 2. To remove the brush, hold the female terminal, which is attached to the brush lead wire, and disconnect the female terminal from the male terminal. 3. Pull the brush straight up out of the brush holder. 4. Replace brushes, in pairs, with original DEWALT brushes available from DEWALT authorized service centers. 5. Ensure that the brushes slide freely in brush box. 6. Reconnect the brush lead wire to brush box terminal. 7. Re-install the brush doors before using the tool. Torque screws to 10 in-lbs, maximum. Overtightening may cause screws to strip. Purchasing Accessories Recommended accessories for use with your tool are available at extra cost from you local dealer or authorized service center. If you need assistance in locating any accessory for your tool, contact: DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286. CAUTION: The use of any other accessory not recommended for use with this tool could be hazardous. Full Warranty DEWALT heavy duty industrial tools are warranted for one year from date of purchase. We will repair, without charge, any defects due to faulty materials or workmanship. For warranty repair information, call 1-800-4-DEWALT. This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces. In addition to the warranty, DEWALT tools are covered by our: 30 DAY NO RISK SATISFACTION GUARANTEE If you are not completely satisfied with the performance of your DEWALT heavy duty industrial tool, simply return it to the participating seller within 30 days for a full refund. Please return the complete unit, transportation prepaid. Proof of purchase may be required. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-DEWALT for a free replacement. To request replacement labels, you will need to know the rated rpm of your tool. The rpm of your tool is stamped into the tool housing. 16 399080-02 rev 11/15/02 10:13 AM Page 17 POUR TOUT RENSEIGNEMENT SUPPLEMENTAIRE SUR CET OUTIL OU TOUT AUTRE OUTIL DEWALT, COMPOSER SANS FRAIS LE NUMERO: 1 800 4-DEWALT (1 800 433-9258) CONSERVER CES DIRECTIVES! MESURES DE SECURITE – GENERALITES AVERTISSEMENT! Lire et comprendre toutes les directives, car le non-respect des directives suivantes pourrait entrainer un risque de choc electrique, d’incendie ou de blessures graves. CONSERVER CES DIRECTIVES ZONE DE TRAVAIL Garder la zone de travail propre et bien ecla...
Questo manuale è adatto anche per i modelli :Rettificatrici - 399080-02 (1.95 mb)
Rettificatrici - D28474 (1.95 mb)
Rettificatrici - D28493 (1.95 mb)
Rettificatrici - D28494 (1.95 mb)