Log:
valutazioni - 2, GPA: 4.5 ( )

Istruzioni per l'uso Campbell Hausfeld, Modello IFT218

Produttore : Campbell Hausfeld
File Size : 1.34 mb
File Nome :
Lingua di insegnamento: enesfr
Vai a scaricare



Facilità d'uso


2. Turn the air tool upside down. 3. Simultaneously (at the same time), pull the trigger and pour a teaspoon of Campbell Hausfeld oil in the air inlet. After an air tool has been lubricated, oil will discharge through the exhaust port during the first few seconds of operation. Thus, the ex-haust port must be covered with a towel before applying air pressure. Failure to cover the exhaust port can result in serious injury. 4. Release the trigger and connect the air tool to the air supply. Cover the exhaust port with a towel then run the air tool for 7 to 10 seconds. Oil will discharge from the exhaust port when air pressure is applied. Continue to run the sander until no oil is discharged. Wipe all residual oil from the tool before use. SPeeD aDjUSTmenT This sander is equipped with a regulator for speed adjustment (See Replacement Parts List for Specifications). aTTaCHInG SanDInG PaD/DUaL aCTIOn SanDerS Adhesive backed discs are recommended. To apply the sandpaper, align outside edge and press self adhesive paper onto the pad. Change sandpaper as needed. Disconnect the air tool from the air supply before attaching the sanding pad. Do not operate the sander if sanding pad is not securely tightened. Always replace a worn or damaged pad. Serious injury could occur. 1. Lock the drive spindle in place before attaching the sanding pad. Rotate the spindle lock until the spindle lock engages with the drive spindle and hand- tighten the sanding pad in a clockwise direction (See Figure 1). Figure 1 Drive Spindle Spindle Lock Operating Postion Pad assembly Postion 2. Unlock the spindle before applying air pressure. nOTe: The spindle lock is for attaching and removing the sanding pad only! Do not operate the tool with the spindle locked or the sander will stall when pressure is applied to the pad. aTTaCHInG SanDInG DISCS/HIGH SPeeD SanDerS 3” or 6” resin discs with non-adhesive backs are recommended. The discs should have 7/8” diameter cutout centers for proper attachment. For best support when using discs larger than 3", use all the backup pads of equal size or smaller than the resin disc itself (See Fig. 2). To install the resin disc, follow the outlined procedures. Figure 2 4-1/2” Backup Pad 3” Backup Pad 5-1/2” Backup Pad Adapter Lock Down Insert Holding Tool Here Disconnect the air tool from the air supply before attaching the sanding disc. Do not operate the sander if sanding disc is not securely tightened or serious injury could occur. 1. Assemble the backup pads as shown in Figure 2. Make sure the recessed center of the pads face the sander. 2. Place the resin disc in front of the appropriate size pad and push the adapter lock down through the center of the pad and discs. 3. Hand tighten the adapter lockdown, then insert the holding tool into the hole shown in Figure 2. Insert a large screwdriver into the slotted hole on the adapter lock down and securely tighten. DUaL aCTIOn SanDerS Begin sanding with an abrasive grit coarse enough to remove the high ...

Questo manuale è adatto anche per i modelli :
Rettificatrici - TL1004 (1.34 mb)
Rettificatrici - TL1005 (1.34 mb)
Rettificatrici - TL1118 (1.34 mb)
Rettificatrici - FHT504 (1.34 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie