valutazioni - 5, GPA: 4.6
(
)
)
|
Facilità d'uso
Wire brushes are equipped with their own threaded hub, simply thread on to spindle. Be sure to seat against shoulder before turning tool “ON”. ! WARNING ! WARNING SPINDLE LOCK RUBBER BACKING PAD SANDING DISC LOCK NUT SPINDLE SPIN-ON WIRE BRUSH WHEEL GUARD INSTALLATION Use wheel guard with disc grinding wheels. Always close the latch to secure the guard. Keep the guard between you and the wheel. Do not direct guard opening toward your body. The position of the guard can be adjusted to accommodate the operation being performed. To attach wheel guard DISCONNECT tool from power source. Open guard release/lock latch and position guard on spindle neck so that the two bumps on guard, line up with the two notches on the spindle neck. Rotate guard either direction to desired position, and close latch to secure guard in place. TO REMOVE GUARD: Open guard release/lock latch, rotate guard until the two bumps on guard line up with the two notches on the spindle neck, and lift guard off the spindle neck. Grinding Assembly BUMPS GUARD RELEASE / LOCK LATCH MOUNTING FLANGE SPINDLE ! WARNING BM 1609929H55 1-05 1/5/05 3:17 AM Page 7 -8- CUP GRINDING WHEELS Use cup grinding wheels for heavy-duty stock removal of metals, concrete and stone. ADJUSTABLE CUP WHEEL GUARD INSTALLATION Open the guard clamp and fit it on the mounting flange then secure by tightening the clamp screw. ALWAYS HAVE THIS GUARD ATTACHED WHEN USING CUP GRINDING WHEELS The adjustable guard allows you to lower or raise the guard’s shell. TO ADJUST: Loosen the four bolts on the shell, and secure the shell for 1/4” wheel exposure for maximum safety. ATTACHING CUP GRINDING WHEEL Thread the cup grinding wheel on the spindle shaft CLOCKWISE. Press in the spindle lock button and turn the cup grinding wheel until the lock button engages, then tighten the wheel securely by hand. TO REMOVE: Reverse procedure. LOCK NUT AND BACKING FLANGE Your tool is equipped with a threaded spindle for mounting accessories. Always use the lock nut and backing flange that has same thread size as spindle. DISC GRINDING WHEEL ASSEMBLY Disconnect tool from power source. Be sure that wheel guard is in place for grinding. When using spin-on grinding wheels, thread directly onto the spindle. When using mounting wheels, thread BACKING FLANGE onto spindle, then place GRINDING WHEEL on the spindle. Thread on the lock nut and tighten nut using a lock nut wrench provided with adapter kit, while holding the spindle lock in. TO REMOVE: Reverse procedure. SIDE HANDLE The side handle used to guide and balance the tool can be threaded into the front housing on either side, and on top of the tool, depending on personal preference and comfort. Use the side handle for safe control and ease of operation. Always use auxiliary handle for maximum control over torque reaction or kick-back. Operation of the grinder without the side handle could cause loss of control of the grinder, resulting in possible serious personal injury. ! WARNING BACKING FLANGE LOCK NUT WHEEL GUARD DISC GRINDING WHEEL SPIN-ON GRINDING WHEEL SPINDLE MOUNTING FLANGE BOLT ADJUSTABLE GUARD CUP GRINDING WHEEL SHELL SPINDLE MOUNTING FLANGE BM 1609929H55 1-05 1/5/05 3:17 AM Page 8 BM 1609929H55 1-05 1/5/05 3:17 AM Page 9 MOUNTING TYPE 28 OR TYPE 29 Only use small flange set (available as GRINDING WHEELS accessory) when mounting type 28 or type 29 ! WARNING To reduce the risk of injury, do not use the flange set wheels (Fig. 1). Refer to figures 2 or 3 for proper wheel provided with your tool for mounting type assembly when using the small flange set. 28 or type 29 grinding wheels. The flanges provided with your tool are not designed for mounting these wheels. SMALL FLANGE SET PART NO. 1 607 000 380 FLANGE WITH SHOULDER FLANGE OR LOCK NUT FIG. 1 FLANGE WITH SHOULDER FLANGE OR LOCK NUT TYPE 28 GRINDING WHEEL SPINDLEFIG. 2 FLANGE WITH SHOULDER FLANGE OR LOCK NUT TYPE 29 GRINDING WHEEL SPINDLEFIG. 3 -9 BM 1609929H55 1-05 1/5/05 3:17 AM Page 10 Operating Instructions "TRI-CONTROL" PADDLE SWITCH The “Tri-Control” Paddle Switch enables the operator to control the switch functions of "Lock-OFF", "ON/OFF" and "Lock-ON". TO UNLOCK SWITCH AND TURN TOOL "ON": Push paddle lever FORWARD (toward the spindle) then squeeze the paddle lever. TO SWITCH TOOL "OFF": Release pressure on paddle lever. The switch is spring loaded and will return to "OFF" position automatically. The "Lock-ON" feature, incorporated into the paddle switch, is a convenience for long operations. TO LOCK SWITCH "ON": After paddle switch has been activated push paddle lever completely FORWARD and release paddle lever. TO SWITCH TOOL "OFF": Squeeze and then release paddle lever. The switch is spring loaded and will return to "OFF" position automatically. !WARNING Hold the tool with both hands while starting the tool, since torque from the motor can cause the tool to twist. Start the tool before applying to work and let the tool come to full speed before contacting the workpiece. Lift the too...
Questo manuale è adatto anche per i modelli :Rettificatrici - 1853-6 (1.25 mb)