valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Aree cords immediately. Damaged cords increase the risk of electric shock. Keep your work area clean and well lit. Cluttered benches and dark areas invite When operating a power tool outside, use accidents. an outdoor extension cord marked "W-A" or "W." These cords are rated for outdoor use Do not operate power tools in explosive and reduce the risk of electric shock. Refer to atmospheres, such as in the presence of “Recommended sizes of Extension Cords” in flammable liquids, gases, or dust. Power the Accessory section of this manual. tools create sparks which may ignite the dust or fumes. Personal SafetyKeep by-standers, children, and visitors Stay alert, watch what you are doing and away while operating a power tool. use common sense when operating a Distractions can cause you to lose control. power tool. Do not use tool while tired or under the influence of drugs, alcohol, or Electrical Safety medication. A moment of inattention while Double Insulated tools are equipped with a operating power tools may result in serious polarized plug (one blade is wider than the personal injury. other.)This plug will fit in a polarized outlet Dress properly. Do not wear loose clothing only one way. If the plug does not fit fully in or jewelry. Contain long hair. Keep your the outlet, reverse the plug. If it still does hair, clothing, and gloves away from not fit, contact a qualified electrician to moving parts. Loose clothes, jewelry, or install a polarized outlet. Do not change long hair can be caught in moving parts. the plug in any way. Double Insulation Keep handles dry, clean and free from oil and eliminates the need for the three wire grease. grounded power cord and grounded power supply system. Before plugging in the tool, be Avoid accidental starting. Be sure switch is certain the outlet voltage supplied is within the .OFF. before plugging in. Carrying tools with voltage marked on the nameplate. Do not use your finger on the switch or plugging in tools .AC only. rated tools with a DC power supply. that have the switch “ON” invites accidents. Avoid body contact with grounded surfaces Remove adjusting keys or wrenches before such as pipes, radiators, ranges and turning the tool .ON.. A wrench or a key that refrigerators. There is an increased risk of is left attached to a rotating part of the tool electric shock if your body is grounded. If may result in personal injury. operating the power tool in damp locations is Do not overreach. Keep proper footing and unavoidable, a Ground Fault Circuit Interrupter balance at all times. Proper footing and must be used to supply the power to your balance enables better control of the tool in tool. Electrician’s rubber gloves and footwear unexpected situations. will further enhance your personal safety. Use safety equipment. Always wear eye Don’t expose power tools to rain or wet protection. Dust mask, non-skid safety conditions. Water entering a power tool will shoes, hard hat, or hearing protection must be increase the risk of electric shock. used for appropriate conditions. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an Tool Use and Care outlet. Keep cord away from heat, oil, sharp Use clamps or other practical way to edges or moving parts. Replace damaged secure and support the workpiece to a -2 BM 1609929C33 10/03 10/28/03 2:49 PM Page 3 stable platform. Holding the work by hand or other condition that may affect the tools against your body is unstable and may lead to operation. If damaged, have the tool loss of control. serviced before using. Many accidents are caused by poorly maintained tools. Develop a Do not force tool. Use the correct tool for periodic maintenance schedule for your tool. your application. The correct tool will do the job better and safer at the rate for which it is Use only accessories that are recom- designed. mended by the manufacturer for your model. Accessories that may be suitable for Do not use tool if switch does not turn it one tool, may become hazardous when used .ON. or .OFF.. Any tool that cannot be on another tool. controlled with the switch is dangerous and must be repaired. Service Disconnect the plug from the power source Tool service must be performed only by before making any adjustments, changing qualified repair personnel. Service or accessories, or storing the tool. Such maintenance performed by unqualified preventive safety measures reduce the risk of personnel could result in a risk of injury. For starting the tool accidentally. example: internal wires may be misplaced or Store idle tools out of reach of children and pinched, safety guard return springs may be other untrained persons. Tools are improperly mounted. dangerous in the hands of untrained users. When servicing a tool, use only identical replacement parts. Follow instructions in Maintain...
Questo manuale è adatto anche per i modelli :Rettificatrici - 1701 (1.18 mb)
Rettificatrici - 1703EVS (1.18 mb)