valutazioni - 6, GPA: 4.7
(
)
)
|
Facilità d'uso
Features This tool includes some or all of the following features. 1. On/off switch 2. Lock-off button 3. Side handle 4. Spindle lock 5. Guard Assembly Warning! Make sure that the tool is switched off and unplugged. Fitting and removing the guard (fig. A) Fitting Place the tool on a table, with the spindle (6) facing up. Hold the guard (5) over the tool as shown. Align the holes in the adjusting plate (7) with the screw holes (8). Press the guard down and insert the screws (9) into the holes. Tighten the screws. Removing Remove the screws (9). Take the guard off the tool. Warning! Never use the tool without the guard. Adjusting the guard (fig. B) The guard can be rotated 180°. Slacken the screws (9) and the nut (10). Rotate the guard as required. Re-tighten the screws and the nut. Fitting the side handle Screw the side handle (3) into one of the mounting holes in the tool. Warning! Always use the side handle. 9 ENGLISH Fitting and removing grinding or cutting discs (fig. C - F) Always use the correct type of disc for your application. Always use discs with the correct diameter and bore size (see technical data). The maximum thickness for grinding discs is 6 mm, for cutting discs 3.5 mm. Fitting Fit the guard as described above. Place the inner flange (11) onto the spindle (6) as shown (fig. C). Make sure that the flange is correctly located on the flat sides of the spindle. Place the disc (12) onto the spindle (6) as shown (fig. D). If the disc has a raised centre (13), make sure that the raised centre faces the inner flange. Make sure that the disc locates correctly on the inner flange. Place the outer flange (14) onto the spindle. When fitting a grinding disc, the raised centre on the outer flange must face towards the disc (A in fig. E). When fitting a cutting disc, the raised centre on the outer flange must face away from the disc (B in fig. E). Keep the spindle lock (4) depressed and tighten the outer flange using the two-pin spanner (15) (fig. F). Removing Keep the spindle lock (4) depressed and loosen the outer flange (14) using the two-pin spanner (15) (fig. F). Remove the outer flange (14) and the disc (12). Use Warning! Let the tool work at its own pace. Do not overload. Carefully guide the cable in order to avoid accidentally cutting it. Be prepared for a stream of sparks when the grinding or cutting disc touches the workpiece. Always position the tool in such a way that the guard provides optimum protection from the grinding or cutting disc. Switching on and off To switch the tool on, press the lock-off button (2) and subsequently press the on/off switch (1). To switch the tool off, release the on/off switch (1). Warning! Do not switch the tool off while under load. Hints for optimum use Firmly hold the tool with one hand around the side handle and the other hand around the main handle. When grinding, always maintain an angle of approx. 15° between the disc and the workpiece surface. Maintenance Your tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Regularly clean the ventilation slots in your tool using a soft brush or dry cloth. Regularly clean the motor housing using a damp cloth. Do not use any abrasive or solvent-based cleaner. Technical data KG2001 Voltage VAC 120/220 Power input W 2,000 No-load speed min -1 8,400 Disc diameter mm 180 Disc bore mm 22 Spindle size 5/8"-11/M14 Weight kg 7 Service You can check the location of your nearest authorized service center by contacting your local Black & Decker office at the address indicated in this manual. 10 ENGLISH Solamente para proposito de Argentina: Importado por: Black & Decker Argentina S.A. Pacheco Trade Center Colectora Este de Ruta Panamericana Km. 32.0 El Talar de Pacheco Partido de Tigre Buenos Aires (B1618FBQ) Republica de Argentina No. de Importador: 1146/66 Tel. (011) 4726-4400 Imported by/Importado por: Black & Decker do Brasil Ltda. Rod. BR 050, s/n° - Km 167 Dist. Industrial II Uberaba . MG . Cep: 38064-750 CNPJ: 53.296.273/0001-91 Insc. Est.: 701.948.711.00-98 S.A.C.: 0800-703-4644 Solamente para propositos de CCA Importado por: Black & Decker LLC Calle Miguel Brostella Final Edificio Milano I, Mezanine 5,6 y 7 El Dorado, Panama Tel. 507-360.5700 Solamente para propositos de Colombia Importado por: Black & Decker de Colombia, S.A. Carrera 85D # 51-65, Bodega 23 Complejo Logistico San Cayetano Bogota - Colombia Tel. 744-7100 Solamente para proposito de Chile: Importado por: Black & Decker de Chile, S.A. Av. Pdte. Eduardo Frei M. 6001-67 Conchali Santiago de Chile Tel. (56-2) 687 1700 Solamente para proposito de Mexico: Importado por: Black & Decker S.A. de C.V. Bosques de Cidros, Acceso Radiatas No.42 3a. Seccion de Bosques de las Lomas Delegacion Cuajimalpa, 05120, Mexico, D.F. Tel. (52) 555-326-7100 R.F.C.: BDE810626-1W7 Black & Decker del Peru S.A. Av. Enrique Meiggs 227. Pque. Industrial - Callao T...