valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean. 7. Do not immerse charger in water or any other liquid. Assembly CAUTION: Before assembly, always ensure that the battery is removed from the tool. Overview (Fig.1) 1. On/Off Switch 2. Battery Pack 3. Random Orbit Sanding Base 4. Large Detail Sanding Base 5. Finger Attachment Sanding Base Random orbit sanding base With this sanding base, you can use the tool as a random orbit sander. Fitting and removing the sanding base (Fig. 2) • Place the sanding base (3) onto the spindle (6). • Place the washer (7) onto the spindle. • Insert the allen screw (8) into the screw hole in the spindle. • Tighten the allen screw using the hex wrench (9) supplied. • To remove the sanding base, remove the allen screw (8) and washer (7). Fitting sanding discs • Hold the tool with the sanding base facing upwards. • Place the sanding disc onto the sanding base (3). The holes in the disc do not need to line up with the holes in the base. Large detail sanding base With this sanding base, you can use the tool as a detail sander or an orbital sander. Fitting and removing the sanding base (Fig. 3) • Place the sanding base (10) onto the spindle (6). • Place the washer (7) onto the spindle. • Insert the allen screw (8) into the screw hole in the spindle. • Tighten the allen screw using the hex wrench (9) supplied. • To remove the sanding base, remove the allen screw (8) and washer (7). Fitting sanding sheets (Fig. 4) • Detach the two diamond-shaped tips (11) from the sanding sheet (12). • Hold the tool with the sanding base facing upwards. • Place the sanding sheet (12) onto the sanding base making sure the holes in the sheet line up with the holes in the base. Diamond-shaped tips (Fig. 5) The diamond-shaped tips (13) can be reversed and replaced when worn. • When the front part of the tip is worn, detach it from the sheet, reverse it and press it onto the sanding base again. • When the whole tip is worn, remove it from the sanding base and fit a new tip. Finger attachment ( Fig. 6) The finger attachment is used for fine detail sanding. • Remove the screw. • Remove the diamond-shaped tip holder from the sanding base. • Fit the finger attachment onto the sanding base. • Fit and tighten the screw. Operation Let the tool work at its own pace. Do not overload. Switching on and off (Fig. 7) • To switch the tool on, press the part of the on/off switch (1) marked “I”. • To switch the tool off, press the part of the on/off switch (1) marked “0”. Dust Collection Note: A vacuum cleaner attachment is available as a service part at extra cost. To find your nearest Black & Decker Service Center location, refer to the yellow pages directory under "Tools—Electric" or call: 1-800-54-HOW-TO (544-6986). WARNING: Collected sanding dust from sanding surface coatings (polyurethane, linseed oil, etc.) can self-ignite and cause fire. To reduce risk, strictly follow sander manual and coating manufacturer's instructions. WARNING: When working on metal surfaces, do not use a vacuum cleaner because sparks are generated. Wear safety glasses and a dustmask. Due to the danger of fire, do not use your sander to sand magnesium surfaces. Do not use for wet sanding. Troubleshooting Problem Possible Cause Possible Solution • Unit will not start. • Battery not installed properly. • Check battery installation. • Battery not charged. • Check battery charging requirements. • Battery will not charge. • Battery not inserted into charger. • Insert battery into charger until red LED appears. • Charger not plugged in. • Plug charger into a working outlet. Refer to “Important Charging Notes” for more details. • Surrounding air temperature • Move charger and tool to too hot or too cold. a surrounding air temperature of above 40 degree F(4,5°C) or below 105 degree F (+40,5°C). For assistance with your product, visit our website for the location of the service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986. Maintenance / Cleaning Use only mild soap and damp cloth to clean the tool. Many household cleaners contain chemicals which could seriously damage the plastic and gel components. Also do not use gasoline, turpentine, lacquer or paint thinners or similar products. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts. Th...
Questo manuale è adatto anche per i modelli :Rettificatrici - FireStorm 5106621-06 (448.47 kb)