valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
CLEANING AND DISPOSAL • All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding project. Vacuum filter bags should be changed frequently. • Plastic drop cloths should be gathered up and disposed of along with any dust chips or other removal debris. They should be placed in sealed refuse receptacles and disposed of through regular trash pick-up procedures. During clean up, children and pregnant women should be kept away from the immediate work area. • All toys, washable furniture and utensils used by children should be washed thoroughly before being used again. Motor Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply. Operating Instructions WARNING: To reduce the risk of serious personal injury, read, understand and follow all important safety warnings and instructions prior to using this tool. SWITCH To turn the tool ON, hold it as shown in Figure 1 and push the portion of the switch marked "I". To turn the tool OFF, push the portion of the switch marked "O". OPERATION Grasp product as shown in Figure 1 and turn it on. Move it in long sweeping strokes across the surface, letting it do the work. Light pressure is all that is required for sanding, polishing or scrubbing. Excessive pressure will slow the tool and produce inferior results. Check your work often, product is capable of removing material rapidly. CAUTION: Under no circumstances should this product be used near water. WARNING: Always unplug product from power supply before any of the following operations. DETAIL SANDING Your tool is equipped with a teardrop base which allows you to use it on large flat surfaces and tight spots or corners. The pad tips may wear unevenly, depending on use. The pads are designed to allow you to interchange and /or rotate the diamond tip. FITTING SANDING SHEETS ( FIG. 2) • Detach the two diamond-shaped tips from the sanding sheet. • Hold the tool with the sanding base facing upwards. • Place the sanding sheet onto the sanding base. The diamond-shaped tip can be reversed and replaced when worn. • When the front part of the tip is worn, detach it from the sheet, reverse it and press it onto the sanding base again. • When the whole tip is worn, remove it from the sanding base and fit a new tip. TIP OF THE SANDING BASE ( FIG. 3) When the sanding base tip is worn, it can be reversed or replaced. • Remove the screw. • Reverse or replace the worn part. • Fit and tighten the screw. FINGER ATTACHMENT ( FIG. 4) The finger attachment is used for fine detail sanding. • Remove the screw. • Remove the diamond-shaped tip holder from the sanding base. • Fit the finger attachment onto the sanding base. • Fit and tighten the screw. MAINTENANCE Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. ACCESSORIES Look for the following MouseTM accessories at your local retailer. Catalog # Description Contents 74-583 120 Medium Sandpaper 5 sheets 74-584 180 Fine Sandpaper 5 sheets 74-585 220 Extra Fine Sandpaper 5 sheets 74-586 Sandpaper Assortment 1 sheet of 120 grit paper, 2 sheets each 180, 220 paper 74-587 Finger Attachment Paper 5 fingers each of 120, 180, 220 74-588 1 OT Power Wool 3 sheets 74-589 4 OT Power Wool 3 sheets 74-581 Polishing Kit 2 sheets of 1 OT power wool, 2 sheets of 4 OT power wool, 2 foam pads 74-582 Scrubbing Kit 2 coarse abrasive pads, 2 fine abrasive pads, 2 foam pads 74-580 Sanding/Polishing Kit 2 sheets of 1 OT power wool, 2 sheets of 180 grit sandpaper, 2 sheets of 240 grit sandpaper, 2 foam pads, 5 finger attachment paper 74-671 Universal Sandpaper/Coarse 5 sheets of 80 grit 74-672 Universal Sandpaper/Med. 5 sheets of 120 grit 74-673 Universal Sandpaper/Fine 5 sheets of 220 grit 74-654 Universal Sandpaper Assortment Recommended accessories for use with your tool are available at extra cost. Listings per retailer may vary. The hook and loop pad and individual bases are replaceable parts. If they become worn, contact your local service center. For more information call: 1-800-54-4-6986. WARNING: The use of any accessory not recommended for use with this tool could be hazardous. Application / Accessory Matrix ACCESSORY RECOMMENDED APPLICATIONS / USES MEDIUM GRIT SANDPAPER PAINT, VARNISH, RUST REMOVAL FINE GRIT SANDPAPER SURFACE BLEN...