valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Se opp! V.r sa vennlig a forst gjennomlese noyaktig denne veiledningen for installasjonen og idriftsettelsen. Huomio! Lue tama ohje huolellisesti lapi ennen asennusta ja kayttoonottoa. Observera! Var god och las noga igenom denna handledning fore installering och idrifttagande.SV ENG FIN NO F ENG ENG Contents 11 Tool Dimensions/Cutting Speeds 1 Specifications 12 Jigs And Push Blocks 2 User Responsibility 13 Controls 3 Standard Delivery 13.1 Definitions 4 Optional Accessories 13.2 Mounting A Tool 5 Final Assembly 13.3 Spindle Speed Setting/Changing 6 Installation 13.4 Tool Height Setting 7 Commissioning 13.5 Fence And Fence Plate Setting 7.1 1-Phase Power Supply 13.6 Cutter Guard Setting 7.2 3-Phase Power Supply 14 Operation 7.3 Direction Of Rotation 14.1 Tools 7.4 Switch 14.2 Stock Prechecking 7.5 Overload Protection 14.3 Moulding Strips 7.6 No-Voltage Release 14.4 Moulding Boards 7.7 Dust Collection 14.5 Making Tenons 7.8 Dust Collector Automatic Start 14.6 Set-In Work 8 Safety Information 15 Care And Maintenance 9 Workpiece Dimensions 10 Scope Of Application 1 Specifications TF 100 M 2.2 WN TF 100 M 2.8 DN Table top 523 x 423 mm 523 x 423 mm Workpiece support area 150-210 x 600 mm 150-210 x 600 mm Working height from floor 850 mm 850 mm Table opening O 150 mm 150 mm Table rings 2 2 Fence travel 30 mm 30 mm Dust extraction outlet O 100 mm 100 mm Max. tool diameter 150 mm 150 mm Max. tool height 60 mm 60 mm Spindle diameter 30 mm 30 mm Spacing collar O 50 mm 50 mm Spindle vertical adjustment 100 mm 100 mm Spindle speeds 4000/6000/7500 min-1 4000/6000/7500 min-1 Motor input capacity P1 2.2 kW S6 - 40% 2.8 kW S6 - 40% Motor output capacity P2 1.1 kW S6 - 100% 1.4 kW S6 - 100 % Operating voltage 220-240 V 1~50 Hz 380-415 V 3~50 Hz Noise Emission The noise emission levels shown below have been established by measuring methods according to: DIN 45 635, part 1651. The A-sound power levels (LWA) were rounded to full dB(A). 1. TF 100 operating under no load A-sound pressure level LpA 77 dB(A) 77 dB(A) A-sound power level LWA 86 dB(A) 86 dB(A) 2. TF 100 operating under load A-sound pressure level LpA 82 dB(A) 82 dB(A) A-sound power level LWA 91 dB(A) 77 dB(A) 2 User Responsibility This machine will perform in conformity with the description contained in the instructions provided. This machine must be checked periodically. Defective equipment (including power cables) should not be used. Parts that are broken, missing, plainly worn, distorted or contaminated, should be replaced immediately. Should such repair or replacement become necessary, it is recommended that such repairs are carried out by qualified persons approved by metabo or its representatives. This machine or any of its parts should not be altered or changed from standard specifications. The user of this machine shall have the sole responsibility for any malfunction which results from improper use or unauthorized modification from standard specifications, faulty maintenance, damage or improper repair by anyone other than qualified persons approved by metabo or its representatives. Metabo reserves the right to change specifications and design without prior notice and without incurring obligation of any kind. Equipment referred to as available or optional may be at extra cost. 3 Standard Accessories Spacing collars: 1 pc. 25 mm, 1 pc. 16 mm, Fence plates 2 pcs. 10 mm, 2 pcs. 8 mm, SUVA style safety cutter guard 2 pcs. 5 mm Tool set Spindle nut: M 30x2 Instructions Fence 4 Optional Accessories Table Extension TF 100 Stock-no. 0914003598 Sliding Carriage TF 100 Stock-no. 0914015600 Moulding Tools see separate catalogue 5 Final Assembly Set table extension level with the table.Install cutter guard carrier on the fence. Use 4 each -hexagon head screw M 6x25 -hex. nut M 6 self-locking Screw both stud bolts into the tapped bore holes of the table. Place fence on table and screw starknobs onto stud bolts. Slide hexagon bar into fence carrier and lock with starknob screw. Install holddown shoe and spring on hexagon bar. Installation Important! This spindle moulder model TF 100 M must be anchored to the floor for stability. A machine not anchored to the floor may fall over while in operation. Use suitable means for anchoring, e.g. anchoring bolts or expansion anchors O 8 mm. 7 Commissioning 7.1 1-Phase Power Supply This machine must be connected to an earthed outlet and operated on a residual current device (RCD) of 30 mA capacity. Supply voltage required 230V ±5% 50 Hz. Protect circuit with a fuse 16 A time-lag. A supply line lead cross section of min. 3 x 2.5 mm2 is required. 7.2 3-Phase Power Supply A 5-wire (L1-L2-L3-N-Earth) supply system is required. Connect with the 16A CEE industrial type plug to an earthed outlet equipped with a residual current device (RCD) of 30 mA capacity. Supply voltage required 400V ±5% 50 Hz. Protect circuit with 3 fuses 16 A time-lag. A supply line lead cross section of min. 5 x 1.5 mm2 is required. 7.3 Direction Of Rotation For mach...