When placing your order, please specify the grain size of the disc desired.
To change the accessory, merely peel off the old accessory, remove dust from the pad if necessary, and press the new accessory in place (Fig. 3). Be sure to align the sanding disc holes with the holes in the backing pad to allow the dust extraction system to function. After considerable service the pad surface will become worn, and the pad must be replaced when it no longer offers a firm grip. If you are experiencing premature wearout of the pad hooks, it may be due to pressure being applied to
n0 No load speed Rotational speed, at no load .../min Revolutions or reciprocation per minute Revolutions, strokes, surface speed, orbits etc. per minute 0 Off position Zero speed, zero torque... 1, 2, 3, ... Selector settings Speed, torque or position settings. I, II, III, Higher number means greater speed Infinitely variable selector with off Speed is increasing from 0 setting Arrow Action in the direction of arrow Alternating current Type or a characteristic of current Direct current Type or
When vacuuming dry dust that is especially detrimental to health or carcinogenic, use a vacuum cleaner that is specifically intended for that purpose. BOSCH VACUUM HOSE DM 2610958399 10-10:DM 2610958399 10-10 i:55 AM Page 10 Introduction INTENDED USE This Bosch Multi-X Oscillating Tool is intended for dry sanding of surfaces, corners, edges, for scraping, for sawing soft metals, wood and plastic components, and for grout removal using the applicable tools and accessories recommended by
Always refer to control panel instructions for proper installation. Introduction 2. 2-1 INTRODUCTION This manual was prepared to assist you in the correct installation, operation, and maintenance of your Liberty pump. Please read it completely before installing the pump. Make certain that you are familiar with the contents, and the chapters on installation and operation are fully understood before running the pump. Liberty Pumps are designed for minimal maintenance. However, regular checks will
Turn the hex socket head cap screw at the center of the cutter wheel on the bottom of the grinder several rotations clockwise. This will insure that the impeller and cutter are free of any seizure due to prolonged storage. If the impeller is not rotated manually prior to installation, the pump may fail to activate. If the impeller’s rotation is difficult or completely resistant, contact the Liberty Pumps Customer Service Department. Mechanical Installation 3-2 STORAGE BEFORE USE Liberty pumps ar
PUMP WILL NOT START 2. REPEATED TRIPPING 3. PUMP WILL NOT SHUT OFF 4. LOW FLOW 5. WATER IN OIL CHAMBER 6. WATER INSIDE MOTOR CASING POSSIBLE CAUSE A. Power supply failure B. Burned out fuse or tripped circuit breaker C. Damaged power cable D. Jammed impeller E. Water inside motor A. Circuit protection under-rated B. Current unbalance C. Pump connected to incorrect voltage D. Wet or damaged wiring E. Obstruction in pump F. Incorrect motor rotation G. Foreign matter build-up A. Control panel failu
The manufacturer shall not be liable under this Warranty if the product has not been properly installed; if it has been disassembled, modified, abused or tampered with; if the electrical cord has been cut, damaged or spliced; if the pump discharge has been reduced in size; if the pump has been used in water temperatures above the advertised rating, or water containing sand, lime, cement, gravel or other abrasives; if the product has been used to pump chemicals or hydrocarbons; if a non-submersib
As the liquid level continues to rise, the “PUMP ON” float tilts. This switch closes, starting the pump. 2. The pump runs until the liquid level falls below the “PUMP OFF” float, emptying the wet well. 3. In the event of a malfunctioning float switch, control relay or pump, the liquid level rises and tilts the “HIGH LEVEL ALARM” float. The alarm system will activate. 4-4.3 FLOAT SEQUENCE-DUPLEX (MANUAL MODELS) 1. As the liquid level in the wet well rises, the “PUMP OFF” tilts, closing the switch
This should be done both phase-to-phase and phase-to-ground. 7. MOTOR OVERLOAD PROTECTION: The pump motor is protected from locked rotor and running overloads by a thermal overload integrally mounted to the motor. No adjustments are required. Check to determine that all grounding connections are made properly 8. If a panel is used, remove all debris, scrap wire, etc., from the control panel interior before closing the doors. Install covers, close doors making certain that no wires are pinched an