valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
Serious injury may result. Keep all loose articles of clothing, ties, jewelery, long hair or other loose objects away from feed opening. Injury may result. Always turn off and unplug the machine before moving, servicing, cleaning or any other conduct other than normal operation. Serious injury may result. 7. Operation Read operating instructions before putting shredder into operation Insert plug in power outlet Install waste bag for shredded material – Open front door and completely remove bag frame from cabinet – Fold new bag around frame. Allow bag to overhang frame by approximately 7" (20 cm). – Slide frame with bag back into cabinet – Close cabinet door. Before start-up – Undo the wing screws securing the unit during transportation Switching equipment ON 1 – Press rocker switch to pos. 1 • Switch locks in "on" position • Equipment is ready for operation (stand by) • Green LED lights – Feed paper • The shredding process is started by photo–cells in the paper feed opening. Insert paper and shredding begins automatically. • When the shredding is complete, the cutting system automatically stops after approx. 3 sec. Switching equipment OFF – Press rocker switch to pos. 3 3 • Switch resets to center position and the machine is turned off. 1.209.999.100 Edition 08/99 USA 420 CC Paper shredder 420 HS 8. Checklist for Inoperative Machine If the equipment does not work properly, please check the following points first: – Is the plug inserted? – Is the switch turned on? – Is the cabinet door closed? – Is waste receptacle full? Empty waste bag. – Is there a paper jam in the shredder? – Is the motor overheated? Switch machine off and allow motor to cool down for approximately 15–20 min. If none of the above applies and the equipment stil does not run, please contact our customer service department. 9. Malfunctions Paper jam Red LED lights • Press rocker switch to center position 2 (2) to stop the cutting system • Press and hold down rocker switch in pos. 3 to reverse the cutting system 3 and back out jammed material (paper is pushed out) Caution! 1 Do notattempt to force the jammed 3 material through the machine by alternating the cutting system between forward and reverse • Remove excess paper 1 • Return switch to pos. 1 and continue shredding in smaller quantities so as not to jam the machine further Note: The 420 HS will not runforward again unless the jammed material has been completely removed from the throat Motor Overheating Red LED lights – Paper shredder switches off automatically. • Press rocker switch to center position 2 (2). • Allow shredder to cool down for approximately 15-20 minutes. 1 • Return switch to "on" position (1) and continue shredding. Cabinet door ajar / bag full Red LED lights – Paper shredder switches off automatically. •Press rocker switch to center position 2 (2). • Make sure cabinet door is properly closed and/or empty waste bag. 1 • Return switch to "on" position (1) and continue shredding. 10. Maintenance (Cross cut unit only) – When shredding capacity drops or the noise increases • Spray special cutting block oil onto cutting system 1 • Run cutting system forward and 3 backward several times without feeding paper • Continue shredding Edition 08/99 1.209.999.100 USA 420 CC 420 HS Paper shredder 11. Warranty 12. Customer Service FELLOWES® POWERSHRED LIMITED United States WARRANTY Fellowes Manufacturing Co. 1789 Norwood Avenue 1 yearon all parts and labor Itasca, IL 60143 5 yearsparts and labor on cutting cylinders Tel.: 1-800-955-0959 Fellowes® warrants this product to be free from Canada defects in material and workmanship for a Fellowes Manufacturing of Canada Ltd. period of one year from the date of purchase by 2750 John Street the original consumer. At it's option, Fellowes® Markham, Ontario L3R 2W4 will repair or replace without charge for material Tel.: 1-800-665-4339 or labor, any component found to be defective during the warranty period. Additionally, the United Kingdom cutting cylinders are warranted for 5 years from Fellowes Manufacturing UK Ltd. the original purchase date and will be replaced Doncaster Road without charge for material or labor if found by Kirk Sandall Fellowes® to be defective. Doncaster, South Yorkshire DN3 1HT Tel.: 01302-885 331 Warranty Exclusions Australia The parties agree that the buyer's sole and Fellowes Manufacturing (Australia) Pty.Ltd. exclusive remedy against Fellowes® shall be for 10 Fellowes Court the repair or replacement of defective parts as Tullamarine, Victoria 3043 provided herein. The buyer agrees that no Tel.: (03) 9330-3211 in Melbourneother remedy (including, but not limited to, 1-800-331-177 outside Melbourne incidental or consequential damages for lost profits, lost sales, injury to property or any other Nederland incidental or consequential loss) shall be Fellowes available to him. This warranty shall NOT apply P.O. Box 180 and is void under the following circumstances: 4130 Ed Vianen 1. When this product or any part thereof ha...
Questo manuale è adatto anche per i modelli :Trituratori - 420CC (63.73 kb)