valutazioni - 5, GPA: 4
(
)
)
|
Facilità d'uso
Bobbin: Inserting & Threading -.......... Picking up Bobbin Thread ......... Removing ................. Winding .................. Buttonholes .................. Buttons .................... Cleaning .................. Connecting Machine .............. Corner, Turning ................ Darning .................... Fastening a Seam ............... Feed Dog Control ............... Hems: Blind Stitched Hem ........ Identification, Head Parts .......... Installing Machine Head in Cabinet ...... Inserting & Removing Material ........ Needle: Needle Size ................. Needle & Thread Chart ........... 26 8 10 6 7 17 21 22,23 4 15 20 1! 15 18,19 2,3 4 14 5 5 Placement ................ 5 Oiling Instructions ............ 22,23 Overcasting Parts List ................ .................. 21 27 Presser Foot, Changing ........... Presser Foot Pressure, Adjusting Sewing Light ................ Stitch Length ................ Stitch Width ................ ...... 15 10 4 11 16 Stitching: Reverse .................. 11 Straight Zigzag Tension: ................ .................. 1 t ,16 16 Upper Lower Thread Thread ............... ............... 12 13 Threading: Bobbin Case ............... 8 Upper Thread ............... Thread Chart ............... 9 5 What To Do ............... 24,25 FRONT VIEW ® // @" q,,, 1. Bobbin WinderSpmdle 8. Feed Dog Controi 15. Presser Foot Screw 2. Bobbin Winder Latch 9. Nomenclature Plate 16. Thread Guides 3. Stitch Width Control I0. Needle Plate 17. Upper Thread Tension Control 4. Stttch Width Limlter 1 t_ Needle Clamp Screw 18. Thread Take-up Lever 5. Stitch Length Control 12. Feed Dog 19. Upper Thread Guide 6. Reverse Stitch Push Button 13. Hand Hole Cover Plate 20. Bobbin Winder Thread Guide 7. Light Switch 14, Presser Foot BACK VIEW @ 26. Clutch Release Regulator 24. Thread Cutter 27. Thread Spool Pins 21. Presser Foot Pressure 23. Presser Foot Lever 22. Face Plate 25. Hand Wheel 28. Blind Stitch Knob {Models 21, 1300 only} INSTALLING MACHINE HEAD IN PORTABLE AND CABINET Loosen the two hinge screws under holes in the rear edge of the machine bed (!). Raise hinge pins in the cabinet cutout (2). Slip machine head onto the pins and tighten hinge screws securely (3). Lower machine head to front flap. Screw spool pins in place. Lay the plastic discs over the spool pins. Discs and pins are packed in the accessory box. SEWING LIGHT (Modets 21, 1300 only) The sewing light is located inside the face plate as shown. It may be turned on or off by pushing the light switch. TO remove the bulb, disconnect the sewing machine and swing open the face plate. Push bulb m slightly, turn it counterclockwise and remove. To replace, push new bulb in and turn clockwise. See illustration 4. CONNECTING MACHINE Push foot or knee control connector onto connector under the machine bedplate, or over the motor. See illustration 5. Push the two prong plug of the control into any 110-120 V° wall outlet. When installing in cabinet, insert grommet with cord in bedplate. NEEDLE THREADTABLE THREAD SIZE _i_-r._EDLE FABRIC ISIZE Cotton 60-100 Synthetic 11 Sheer cottons, Fine Laces silks, and synthetics Silk A Cotton 60-80 Medium weight cottons Mercerized 50 14 Medium weight silks Synthetic Medium weight synthetics Silk A Light weight woolens Cotton 40-60 Heavy weight cottons Mercerized 50 16 Medium to heavy weight woolens Mercerized heavy duty Heavy drapery fabrics Cotton 30-50 18 Heaviest cottons as for men's work clothes Mercerized heavy duty Heaviest woolen coating NEEDLE 51ZE Use KENMOtLE needles. The size of the needle should conform to the size of the thread and both should be suitable to the material. The same size thread should be used in the bobbin as on the upper part of the machine for ordinary sewing. Never use a bent needle nor one with a blunt point. This is the exact length of the needle to be used in your machine. Comparison with this illustration will determine t whether the needle you have is the cor rect one for your machine. PLACEMENT OF NEEDLE Raise take-up lever to its highest positron by turning hand wheel toward you. Loosen needle clamp screw. Hold needle so that the fiat side is to your nght, slip bhmt end of needle as far as _t will go into needle clamp. Tighten needle into place with clamp screw. Flat side faces to righ t. REMOVINGBOBBINCASEFROMSHUTTLE Take up lever at its highest position. t 1/ Pull out latch. .° Pull bobbin / case straight out. WINDING THE BOBBIN Place thread on spool post. Draw thread as shown. 0 Wind thread around bobbin a few times, front to back. 0 Place bobbin onto bobbin winder shaft. Push bobbin winder latch until it clicks. 0 Release clutch by turning clutch knob toward you. 8tart machine. 0 When bobbin is full, winding mechanism stops. 0 Tighten clutch knob and remove bobbin. INSERTINGBOBBININTO BOBBINCASE_CASEiNTO SHUTTLE O" Guide bobbin onto center pm of bobbin case. Pull thread through slot. Pull thread under tension spring. _IP Holding latch, position case into shuttle, ...
Questo manuale è adatto anche per i modelli :Macchine per cucire - 1300 (1.38 mb)