Log:
valutazioni - 1, GPA: 5 ( )

Istruzioni per l'uso Sears, Modello KENMORE 385. 1274180

Produttore : Sears
File Size : 3.48 mb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


a. b. Carefulfy mark the buttonhole length on your garment, Change to the buttonhole guide 2. a. Move the slider so that the top slider meets the (A) toward you marl{ {C) on the start mark (B), 3. a. b, Set the stitch selector at tiE] , Sew forward until you reach the front marking of your button- foot. b. Line up the markings on the hole. c, insert the garment under the foot with the top mark on your c. Stop sewing at the left stitch, ._%ttonhole guide foot foot with the buttonhole mark-garment. ing running toward you, c. Lower the presser foot. NOTE: The markings on the slider are engraved m centimeters. Adjusting the Stitch Density Depending upon your fabric or your own preference in buttonholes, you may alter the buttonhole stitch density within the blue buttonhole @ Coarse @ Fine range on the stitch length dial. stitches 1. For less density, turn the diat lot heavv tabrics _ _ stitchesfor light labncs toward "24" 2. For more density, turn the dial toward "0", NOTE: Always make a practice buttonhole on a scrap fabric you plan to use to find the more \ /@ suitable stitch length. 39 Buttonholes (Continued) 4, a. Set the stitch selector at _"_14 5, a, Set the stitch selector at [_L 6. a. Set the stitch selector at=_. 7. Remove the fabric and cut the hole open with the buttonhole opener in b. Sew 4 to 6 stitches. b, Sew 4 to 6 stitches, b, Sew until you reach the back of the buttonhole. your accessory box, c, Stop sewing at the rtght stitch. c, Stop sewing at the left stitch, c. Stop sewing at the right stitch, 4O Sew in a Zipper: Set the Machme St=tch selector ot openmg Top thread tenstot_ Stitch length 12 control 3 tO 6 Top edge of fabric Fabric Preparation: Put the top sides of the fabric together and sew to the end of the zipper opemng, Use the reverse to iock the stitches. Sew the zipper opening wroth stitch length at "6" and top thread tension at "3", Zipper tape To Sew: 4. To sew the left side of the ztpper, set the zipper foot on the left side 1. Fold back the left seam allowance of the needle. as shown. 5, Lower the zipper foot on the right 2, Turn under the r_ght seam allowance to form a 1/8" fold, s_de at the bottom of the zipper so that the needle pierces the fold 3. Place the z_pper teeth next to the and the zipper tape. 1/8" fotd and pin m place, 6. Sew through the fold and the zipper tape to the point where the slider begins, 7, Lower the needle to hold the fabric and raise the presser foot. Sew in a Zipper (Continued) J 8. Open the zipper. 10, Close the zipper and turn the I1, To sew the right side of the zip9, Lower the presser foot and stitch fabric top side up. per, set the zipper foot on the the rest of the seam. right side of the needle. 12. Stitch across and below the bottom of the z_pper. 13, Turn the corner and continue to INVISIBLE ZIPPER AND CORDING guide the foot along the zipper INVISIBLE ZIPPER teeth_ as shown, Adiust the toot so the needle _ssewing through Stitch through the fabric and the the center hole ot the foot and one 8roove foot ts riding on the teeth of the zipper of as zipper tape, shown. Follow the zipper manufacturer's instructfons, After zipper has been inserted, f_nish sewing seam by shifting foot to side pos_tlon sewing through side notch, CORDING \ Foot can also be used to make cording for slip* covers etc, Cover a cord with 8 strip of b_as fabric and sew as shown. NOTE'. Use "Low Bar Sewing Machine ZIPPER FOOT" {6757) for "qnvlsib|e z_pper'" and "cording", which can be obtained at any Sears retait store. 14. Stop about 2" from the top of the z!pper. 15, Lower the needle into the fabric and raise the presser foot, 16, Remove the basting stitches and open the ztpper. 17, Lower the foot and stitch the rest of the seam, Make sure the fold Is even. Shell Stitch ing (M odels 12741 and ;12641) Set the Machine Stitch selector 1 ! Set the Machine Stitch selector0 Top thread tension control 3 to 9 Strtch length t 2 to 24 Here's How Top thread ter_sJon control I to 4 Stitch length 1. For best effect-Zigzag foot --set the stitch length as you desire, --you may need to tighten the top thread tension slightly, --allow the needle to just clear the fotded edge of the fabric when it zigzags. Zigzag foot The Stitch and Its Uses The Shell Stitch is formed by sewing a blind hem over folded fabric. Several rows of shell stitching are called shell tucks. Shell stitching can be used to finish hems_ s_eeve and neck openings, 2, You soft tf you sew rows of shell stitches, space the rows 1/2" apart, can sew Shell Stitch on knits or silky wovens in any direction. With the stitch length at "6"_ sew straight stitching lines 3/8" (1 cm) apart across the area to be smocked, Knot the threads along one edge, Pull the bobbin threads and distribute the gathers evenly,. Secure the threads at the other end. Sew the decorative stitch between the gathering stitches. Pull out the gathering stitches. She_! tucking can scalloped tucks linger_e, be on used to blouses create and NOTE; Loosen tensEon easi...

Questo manuale è adatto anche per i modelli :
Macchine per cucire - KENMORE 385. 1264180 (3.48 mb)
Macchine per cucire - KENMORE 385. 1254180 (3.48 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie