valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
Turn over the fabric. Button sewing 2.G-7.0 Change the presser foot to the button sewing foot. I.Move the drop feed control to n^rr" to lower the feed dogs. 2. Position the work under the foot. Place the button in the desired position, lower the foot. 3. Select zig zag pattern. Adjust the stitch width to "2.0-7.0" according to the distance between the two holes of the button. 4. Turn the handwheel to check that the needle goes cleanly into the left and right hoies of the button. 5. Before sewing, press the Auto-lock button to sew reinforcement stitches automatically at the beginning and at the end of the stitch. If a shank is required, place a darning needle on top of the button and sew. 6 For buttons with 4 hoies, sew through the front two holes first, push work forward and then sew through the back two hoies. Buttonhole stitching 19 #fe 20 21 III«» 22 —---- 2.5-7.0 0.3-1.0 —"''na/X ---- i7; For thin or medium fabric 18: For horizontal holes on blouses or shirts made from thin or medium fabric 19: For thin or medium fabric 3.Q~7.0 0.3-1.0 20: For suits or overcoats 21: For thick costs : 22: For jeans or trousers ---- 2.5-5.S 0.3-1.0 '•'•'WA ----— 5.5-7.0 0.3-1.0 £ Please Note: Before sewing a buttonhole on your project, practice on a scrap piece of the w same type of fabric. ■m : II ' 111 ■:jf ■# 1 : ill . : -a I iip m fabric. The maximum buttonhole length is 3cm (1 3/16 inch). (Total of diameter + thickness of button.) button holder plate and insert the button. The size of the buttonhole is determined by the button inserted in the button plate. The thread should be passed through the hole in the presser foot, then be placed under the foot. Buttonhole stitching n©n h limp XL—. ^ Vs irir-- Starting point fZ PIJSHU 3. Select the buttonhole stitch. Adjust the stitch width and the stitch length to the desired width and density. 4. Position the fabric under the presser foot so that the centerline's mark is aligning with the center of the buttonhole foot. Lower the buttonhole lever, then push it to the back. Please Note: The warning symboi will utt ou/crc?/i it ti i c? uunut tt lever is on upper position when you select any buttonhole pattern and press the " Start/stop " button. 5. Before sewing, please hold the thread by hand. Please Note: Gently feed the fabric by hand. Before stopping, the machine wili automatically sew a reinforcement stitch after the buttonhole is sewn. 37 6. Buttonholes are sewn from the front of the presser foot to the back, as shown. 7. Raise the presser foot and cut thread. To sew over same buttonhole, raise the nraccor fr’irvt Aa/MI mti jrn tn nrininai f->i vuuui i l ynwiii luiuii i i.v_i ui u wi ly ► After sewing the buttonhole stitch, raise the buttonhole lever until it stops. Please Note: After finishing the buttonhole stitch, LCD screen will be demonstrated the warning animation rTt/li'f'Irtrt Wii'rt/'ii/ «-f jV' mmin/4 i/mi i i jcoocjL/w usojjiay, a ta tu i a i itt /lj ywu tv lift the buttonhole lever. Buttonhole stitching s«m •• •• • • • • 8. Cut the center of the buttonhole being carefui not to cut any stitches on either side. Use a pin as a stopper at the bartack so you do not cut too much. I* Making a buttonhole on stretch fabrics When sewing buttonholes on stretch fabric, hook heavy thread or cord under the buttonhole foot. 1. Attach the buttonhole foot and hook the gimp thread onto the back of the presser foot. Bring the two gimp thread ends to the front of the foot and insert them into the grooves, then temporarily tie them there. Lower the presser foot and start sewing. Set the stitch width to match the diameter of the gimp thread. 2. Once sewing is completed, pull the gimp thread gentiy to remove any slack, then trim off any excess. Please Note: It is suggested that you use interfacing on the backside of the fabric. 39 Eyelet stitch ■— 5.0 6,0 7,0 23: Select for sewing eyelets on belts , etc A B C $ => ■=?> tj 1. Select pattern 23 to get the eyelet stitch. Attach presser foot "A". 2. Press the or"+" stitch width adjustment to button select the eyelet size. Size of eyeiet. A. Large: 7.0mm (1/4 inch). B. Medium: 6.0mm (15/64 inch). C. Small: 5.0mm (3/16 inch). 3. Lower the needle into the fabric at the beginning of the stitching, and then lower the presser foot Sever. Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. 4. Make a hole at the center using an eyeiet punch. * Eyelet punch is not included with the machine. Please Note: If thin thread is used, the stitching may be coarse. If this occurs, sew the eyelet twice one on top of the other. 40 01 CD I I t I —---- 3,5 : 1.5-3.0 Attention: Zipper foot must be used for sewing the straight stitch with center needle position (3.5) only. It is possible that needle could hit the presser foot and break when sewing other patterns. inserting a centered zipper 1. Baste the ...
Questo manuale è adatto anche per i modelli :Macchine per cucire - STYLE-MAKER 3100 (4.65 mb)