valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
1 Baste the cutout to the fabric at the desired location. 2 Carefully sew around the edge of the cutout using a Zigzag Stitch with a fine stitch length. 3 Cut away any fabric that is left outside the stitching. 4 Remove the basting, if necessary. Memo . Make reinforcing straight stitches at the beginning and the end of the stitching to secure it. CAUTION . Be careful that the needle does not hit a pin during sewing, as the needle can break. You may also be injured. Stitch Name Pattern Stitch Length [mm (inch)] Stitch Width [mm (inch)] Foot Zigzag Stitch Any Any None ¦ Preparing for sewing a Monogram and Embroidering 1 Place the darning plate on the needle plate. (On a machine equipped with a drop feed lever, lower the feed dogs by setting the drop feed lever to the up position.) 2 Set the pattern selection dial to the Zigzag Stitch. 3 Draw the lettering (for monogramming) or design (for embroidering) on the surface of the fabric. 4 Stretch the fabric between embroidery hoops as firmly as possible, with the underside of the fabric on the bottom of the inside hoop. 5 Put the work under the needle with the presser foot holder assembly removed. 6 Pull the lower thread up through the work at the starting position by turning the balance wheel, and then make a few holding stitches. 7 Grip the hoop with your thumbs and forefingers while pressing the fabric with your middle and third fingers and supporting the outside of the hoop with your little fingers. Note . After sewing without feeding, prepare for the next seam by returning the drop feed lever to the down position so that the feed dogs are raised. CAUTION . Keep fingers away from moving parts, especially needles. ¦ Monogram 1 Sew by moving the hoop slowly along the lettering at a constant speed. 2 Secure with a few straight stitches at the end of the last letter. ¦ Embroidering 1 Stitch the outline of the design by moving the embroidery hoop. 2 Fill in the design alternating from the outline of the design to the inside and from the inside to the edge of the outline until the design is completely filled in. Keep the stitching close together. Memo . You can make long stitches by moving the embroidery hoop rapidly and short stitches by moving it slowly. 3 Secure with a few straight stitches at the end of the design. CAUTION . Keep fingers away from moving parts, especially needles. KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————— 38 MAINTENANCE Changing the Light Bulb 1Remove the power supply plug from the outlet. 2Loosen the face plate screw. 3Remove the face plate from the machine as shown below. Note . Use only a bulb of the same type and rated 15 W. 4Replace the sewing light bulb. 1 Bulb 2 Loosen 3 Tighten 5Reattach the face plate and fasten the screw. Oiling 1Remove the power supply plug from the outlet. 2Remove the needle plate and the face plate, and then put 2 to 3 drops of oil at each point indicated by the arrows. 3Operate the machine at a fast speed for a short time without thread installed. 4Be sure to wipe any excess oil off the machine. 1 3 2 Cleaning ¦ Removing the Shuttle Hook 1 Raise the needle to its highest position and unplug the machine. 2 Remove the extension table and open the shuttle cover on the front of the free arm. 3 Take the bobbin case out of the shuttle race by opening and pulling the latch. 4 Slide the latch levers away from the retaining ring to remove it. 1 2 1 Retaining ring 2 Latch lever 5 Remove the hook by grasping its center post and pulling it out. 3 54 2 1 1 1 Retaining ring 2 Latch lever 3 Hook 4 Driver 5 Race body Note . When the needle is lowered, the shuttle hook cannot be removed. ¦ Cleaning the Shuttle Race 1 Remove any accumulated lint and thread from the retaining ring, hook, driver and race body with a brush. 2 Wipe lint from the shuttle race using a cloth dampened with machine oil. 3 Clean the shuttle hook as described in step 2. 4 When reinstalling the removed parts, hold the retaining ring in place with the notch at the top while pushing the latch levers back to their original positions. ¦ Cleaning the Feed Dogs 1 Remove the needle plate by removing the screws with a coin. 2 Clean the upper part of the feed dogs and shuttle race body with a brush. KNOWING YOUR SEWING MACHINE Performance Checklist Whenever sewing difficulties are encountered, first review the manual section about the operation that you are performing, to make sure you are using the machine correctly. If the problem persists, the following checklist may help improve the operation. If you still have difficulties, contact your nearest service center. FABRIC UPPER THREAD LOWER THREAD SKIPPED LOOP IN SEAM PUCKERS BREAKS BREAKS STITCHES Lower thread is Needle is incor-Thread tension is Thread tension is tangled. rectly inserted. incorrect. too tight. Upper threading is not correct. Page 18 No Page 16 No Page 8 No Page 22 No Page 22 No Bobbin is not Upper thread is threaded properly Inferior needle is tangled. in the shuttle u...
Questo manuale è adatto anche per i modelli :Macchine per cucire - XL-5600 (1.83 mb)
Macchine per cucire - XL-5500 (1.83 mb)
Macchine per cucire - PS-21 (1.83 mb)