valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
– Use a stabilizer that is larger than the size of the hoop so that the entire stabilizer can be hooped with the cloth as shown in the diagram. This is to prevent the fabric from sagging. 1 Size of embroidery hoop 2 Stabilizers – When embroidering heavyweight fabrics or fabrics that cannot be ironed, you can use the stabilizers by placing them under the cloth without actually attaching it. Upper thread - embroidery thread #50 THREAD Bobbin thread - embroidery bobbin thread (X81164-001) Perfect needlework cannot be guaranteed with the use of other threads. Home sewing machine needle 75/11 NEEDLE Do not use ballpoint needles. * Use Brother embroidering thread (X81164-001) for the bobbin thread. Types of embroidery frames Medium frame 1 10 cm (H) . 10 cm (W) Small frame (Optional) 2 2 cm (H) . 6 cm (W) (for embroidering initials) CAUTION Depending on the size of the pattern and the position of the pattern to be embroidered, it may not be possible to use the small frames. When using this frame, be sure to check the layout screen display (refer to page 83) before starting to embroider any patterns. If the frame are used by mistake, the presser foot may strike the frame, which could cause injury. Basic Patterns Error Patterns Contents Setting Machine Utility Embroidering Maintenance Troubleshooting Sewing (Programmed Messages (Memory Operation in Machine) Setting the fabric into the embroidery frame 1. Mark the fabric using a chalk pen or fabric marking pen to indicate the embroidering position. 1 2 3 4 2. Loosen the adjusting screw and separate the inner and outer frames. Lay the fabric on top of the outer frame and secure it between the inner and outer frame, and tighten the adjusting screw just enough to secure the fabric. Gently remove the fabric from the frame without loosening the adjusting screw. * Be sure to align the mark on the inner frame with the ( ) mark on the outer frame. 1 Inner frame 2 Outer frame 3 Loosen 4 Adjusting screw 3. Tighten screw of outer hoop to hold fabric and inner hoop in place. Remove fabric and inner hoop. (For best results lay the outer frame on a flat table surface and lay the fabric on top of it.) 1 2 4. Place the embroidery sheet into the inner frame, while matching lines on the sheet with mark on fabric. 1 Inner frame 2 Standard line Basic Patterns Error Patterns Contents Setting Machine Utility Embroidering Maintenance Troubleshooting Sewing (Programmed Messages (Memory Operation in Machine) 75 5. Press down into the outer frame so that the mark doesn’t move out of place. 1 Outer frame 2 Inner frame 3 Surface of fabric 1 2 3 * Press down firmly until the outer frame and inner frame are at the same height. 1 6. Remove the embroidery sheet before starting to embroider. 1 Finger hole for removing grid Basic Patterns Error Patterns Contents Setting Machine Utility Embroidering Maintenance Troubleshooting Sewing (Programmed Messages (Memory Operation in Machine) 77 Contents Setting Up Basic Sewing Machine Operation Utility Stitches Embroidering Maintenance Troubleshooting Error Messages Sewing Chart Patterns (Programmed in Machine) Patterns (Memory Card) Fitting the embroidery frame to the embroidery unit 5 3 1 2 1. Raise the presser foot to its highest position. Then pass the embroidery frame under the presser foot with the mounting bracket on the left side and the fabric right side up. 2. Align the two pins on the embroidery unit frame holder with the mounting bracket on the frame, and then press the frame into the embroidery unit frame holder until a click is heard. CAUTION Always make sure to attach the hoop by both pins. If the hoop is not firmly attached, it could mess up your stitching. 1 Embroidery arm frame holder 2 Pins CAUTION Be sure to wait until the embroidery unit has finished initializing before fitting the embroidery frame. (Refer to page 65.) Removing the embroidery frame 5 3 1 2 1. While holding the frame with both hands, pull the front of the hoop up to lift it out of the front pin. 2. Then pull the back of the hoop up to lift it out of the back pin. 3. Raise the presser foot lever, then pull frame out from under foot. 1 2 Embroidering CAUTION – When sewing embroidery, Brother embroidering thread (X81164-001) must be used for the bobbin thread. – Check bobbin thread before beginning to sew. If you embroider when the bobbin thread is low, the thread could tangle up or other problems could result. – If you are using the embroidery unit, the foot controller cannot be used at this time. Example : 1. Select the desired pattern. The order of sewing for each part will be displayed. * 1/4 indicates that the picture displayed to the left is for the first color to be stitched of a four-color design. * The color displayed above each pattern is suggested color to use. · Some parts may not have a color displayed above them; you can sew these parts with any color you like. · Refer to Color screen. 2. Thread the needle for the first color and pass it through embroidery foot...