valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
4. Set the presser foot in the 3 mm (1/8'') margin. Starting from the end of the zipper opening. Sew to a point about 50 mm (2'') from the edge of the fabric, then stop the machine. Pull down the zipper slider, then continue sewing to the edge of the fabric. 1 50 mm (2'') 2 3 mm (1/8'') CAUTION Make sure the needle does not strike the zipper during sewing. If the needle strikes the zipper, the needle may break, leading to injury. 49 PATTERNS CONTENTS BEFORE SEWING UTILITY MAINTENANCE SEWING (PROGRAMMED MACHINE) 6 12341236 1234123 5. Close the zipper, turn the fabric over, and sew a basting stitch. 1 Front of the skirt (wrong side of fabric) 2 Basting stitches 3 Front of the skirt (right side of fabric) 4 Back of the skirt (right side of fabric) 6. Remove the presser foot, and reattach it so that the left side of the pin is attached to the presser foot holder. 1 Right 2 Left 3 Needle drop position 7. Set the fabric so that the left edge of the presser foot touches the edge of the zipper teeth. Sew reverse stitches at the top of the zipper, then continue sewing. Stop sewing about 50 mm (2'') from the edge of the fabric, leave the needle in the fabric, and remove the basting stitches. Open the zipper and sew the rest of the seam. 1 Basting stitches 2 7 to 10 mm (1/4'' to 3/8'') 3 Reverse stitches 4 50 mm (2'') PATTERNS CONTENTS BEFORE SEWING UTILITY MAINTENANCE SEWING (PROGRAMMED MACHINE) 50 J DART SEAM 1 1. Attach presser foot “J”, then sew a reverse stitch at the beginning of the dart and sew from the wide end to the narrow end without stretching the fabric. 1 Basting 2. Do not sew a reinforcement stitch at the end. Cut the thread at the end leaving an excess 50 mm(2"), and then tie both ends together. 3. Insert the ends of the thread into the dart using a needle. 4. Iron the dart to one side so that it is flat. PATTERNS CONTENTS BEFORE SEWING UTILITY MAINTENANCE SEWING (PROGRAMMED MACHINE) 51 GATHERING J For the waists of skirts, the sleeve openings of shirts, etc. 1. Press the stitch length manual change key to turn on the LED lamp. 2. Move the stitch length adjustment lever up to increase the stitch length (about 4 mm (1/16")) as shown left figure, and select a weak thread tension. 3. Attach presser foot “J”, then pull out about 50 mm (2") of both the bobbin and upper threads. 1 Upper thread 2 Bobbin thread 3 About 50 mm (2") 4. Sew two rows of straight stitches parallel to the seam line, then trim off the excess thread leaving 50 mm (2") . 1 Seam line 2 10 to 15 mm (3/8" to 9/16") 3 About 50 mm (2") 5. Pull the bobbin threads to obtain the desired amount of gather, then tie the threads to secure them. 6. Smooth the gathers by ironing them. PATTERNS CONTENTS BEFORE SEWING UTILITY MAINTENANCE SEWING (PROGRAMMED MACHINE) 52 Pulling up the bobbin thread 1. Pass the thread along the groove in the direction of the arrow, and leave it there without cutting it. 1 Shuttle * The bobbin cover should still be removed. 6 2. While holding the upper thread, press the “NEEDLE POSITION” button twice, and then pull out the bobbin thread. 3. Replace the bobbin cover. PATTERNS CONTENTS BEFORE SEWING UTILITY MAINTENANCE SEWING (PROGRAMMED MACHINE) 53 II PINTUCK For decorating blouses, etc. I 1. Mark along the folds on the wrong side of the fabric. 1 Wrong side of fabric 2. Fold the fabric so that the right side faces upward and iron only the folded parts. 1 Right side of fabric 3. Attach the right pin of presser foot “I” to the holder, and sew a straight stitch along each fold. 1 Width for pintuck 2 Wrong side of fabric 3 Right side of fabric CAUTION When using zipper foot “I”, make sure the straight stitch, middle needle position is selected. Turn the balance wheel to make sure the needle does not strike the presser foot. If another stitch is selected, the needle will strike the presser foot, causing the needle to break and possible leading to injury. 4. Iron all folds in the same direction. PATTERNS CONTENTS BEFORE SEWING UTILITY MAINTENANCE SEWING (PROGRAMMED MACHINE) 54 J FLAT FELL SEAM For reinforcing seams and neatly finishing edges 1. Attach presser foot “J”. Sew the seam line, then cut half of the seam allowance from the side that the flat fell seam will lie against. 1 About 12 mm (1/2") 2 Wrong side of fabric 2. Spread out the fabric along the finish line. 1 Finish line 2 Wrong side of fabric 3. Lay both seam allowances to the shorter one’s (cut one) side and iron them. 1 Wrong side of fabric 4. Fold the longer seam allowance around the shorter one, and sew the edge of the fold. 1 Wrong side of fabric * Flat-fell seam can be on the inside or outside. For example for denim jeans, jackets, etc., seam is on the outside, rather than inside as shown above. PATTERNS CONTENTS BEFORE SEWING UTILITY MAINTENANCE SEWING (PROGRAMMED MACHINE) 55 Finished flat fell seam 1 Right side of fabric PATTERNS CONTENTS BEFORE SEWING UTILITY MAINTENANCE SEWING (PROGRAMMED MACHINE) 56 APPLIQUES 3 16 J 1. Use a temoprary spray adhesive, fabr...