valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
• Do not run the engine in an enclosed and/or poorly ventilated area. The gas of the engine contains carbon monoxide, which is dangerous to your health. • Work only when there is sufficient light. • Do not use the blower when it is raining or when the grass is wet. • Caution must be taken while blowing on slopes. • Turn off the engine if you must leave the blower unattended. • Never change the rated speed of the engine in any way. • Stop the engine and remove the spark plug cover in these cases: - Before any maintenance, repairing or checking operations. - If you leave the blower unattended. - If the blower vibrates in an abnormal way, take the blower to an authorized service centre. - Check the bolts and nuts regularly. Bolts and nuts may vibrate loose over time. WARNING. Fuel is highly flammable. • Keep fuel in a jerry can specially made for this purpose. • Fill the fuel tank with a funnel and outside. Do not smoke or use a mobile phone during this process. • Fill with fuel and oil before starting the engine. Never open the cap of the fuel tank to add gasoline while the engine is running or still hot. • Do not start the engine if there is spilt fuel on the blower or in the area surrounding. Take the blower away from the zone where fuel has been split and avoid any contact from a hot source as long as the split gasoline is completely evaporated. • Tighten the fuel tank cap and jerry can cap tightly. Additional safety rules for petrol blowers • Do not operate in a hazardous location. Such areas include where there is a risk of explosion of petrol fumes, leaking gas or explosive dust. • Do not operate in a confined area. Exhaust gases, smoke or fumes could reach dangerous concentrations. • Protect your blower. This blower is NOT WEATHERPROOF and should not be exposed to direct sunlight, high ambient temperature and damp, wet or high humidity conditions. • Do not smoke while refuelling. This is potentially dangerous as it may ignite the fuel and cause an explosion. • Take care not to spill fuel. When refuelling the blower ensure that the motor has been switched off. Prevent the spilling of fuel as this may also ignite with the hot motor. Never refuel whilst the engine running. • Be careful where you store the blower. Store the blower in a dry area away from flammable liquids. • Keep your distance. The blower emits exhaust fumes. Ensure bystanders keep a safe distance. • Ensure you use oil-mix fuel. Ensure that you mix 40 parts unleaded fuel to 1 part engine grade oil. If not, the engine will overheat and cause damage to your blower. • Never fill fuel tank indoors. Never fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank. • Stop the engine before re-fuelling. • Stop the engine and disconnect the spark plug wire: – If the blower starts to vibrate abnormally (find and remove the cause of the vibration immediately). • Reduce the throttle before turning off the engine and turn the fuel off when you have finished blowing. • The user is responsible for the safety of other people, animals and objects in the working area. Keep children and domestic animals at a safe distance while the blower is in use. Unpacking Due to modern mass production techniques, it is unlikely that your petrol blower is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Contents of carton • Tube (2 pieces) • Screws for tube assembly • Fuel mixing bottle Know your product 1. Throttle trigger 2. Rubber grip handle 3. Motor 4. Straight tube 5. Nozzle tube 6. Recoil starter 7. Petrol cap 8. Spark plug 9. Primer 10. Air filter cover 11. Outlet exhaust 12. OFF button 13. Tube locking screw 14. Fuel tank 15. Choke 16. Sliding throttle lock 16 12 11 5 4 13 2 1 10 8 15 6 3 7 9 14 Assembly IMPORTANT. Blower tube installation affects both blower balance and performance. Both tube and nozzle must be screwed together. WARNING. Danger from rotating impeller! Stop the engine before installing or removing the blower tubes. Never perform any maintenance or assembly procedures on this machine while the engine is running. 1. Place the blower upright on the ground or on a sturdy work surface. 2. Push the nozzle tube (5) over the straight tube (4) lining up the locking pins. 3. Rotate the nozzle tube clockwise locking it into place. 4. Lock the tubes together using the 2 screws provided. 5. Push the assembled blower tube over the discharge port and rotate until locks in place and the screw hole can be seen. 6. Rotate the tube to the desired position. 7. Screw the tubes using the screws provided. Mixing the fuel ENGINE FUEL: MIX AT 30:1 30:1 IMPORTANT. Use good quality air cooled 2-stroke engine oil. This product is powered by a 2-stroke engine and requires pre-mixing fuel with 2-stroke oil. 1. Use fresh unleaded petrol. You must use 100% synthetic oil specifically made for he...
Questo manuale è adatto anche per i modelli :Sistemi di ventilazione - PB26CC (1010.04 kb)