valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
• Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision. • The operation of any mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your mower or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. -Use only an approved container. -Never remove gas cap or add fuel with the engine running. -Allow engine to cool before refueling. -Do not smoke. -Never refuel the machine indoors. -Never store the machine or fuel container inside where there is an open flame, such as a water heater. • Never run a machine inside a closed area. • Keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in good condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage. Allow machine to cool before storing. • Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting. • Never make adjustments or repairs with the engine running. • Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer’s recommended parts, when necessary. • Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them. • Check brake operation frequently. Adjust and service as shown in the Operator’s Manual. 6 UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton. TOOLS REQUIRED • 7/16" Wrench or ratchet and socket • ." Wrench or ratchet and socket • ." Wrench • Drill and 3/8" bit • Torque Wrench • Hacksaw • Hammer NOTE: When right hand (RH) and left hand (LH) are mentioned in this manual, it means when you are seated on the mower in the operator’s position. Upper Chute Bag Dump Indicator Blower Housing Middle Chute CONTAINER CONTENTS • Blower Assembly • Containers • Belt • Seal Fastening Kit • Mounting Brackets • Bag of Hardware Belt Cover CAUTION BEFORE ASSEMBLING GRASS CATCHER TO MOWER: • Set parking brake. • Place motion control levers in “NEUTRAL” position. • Turn ignition key “OFF” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug and place wire where it cannot come in contact with plug. ASSEMBLY 7 1. Slide the flanges of the support assembly in the slots in the drawbar. 2BAGGER SUPPORT ASSEMBLY 2. Pivot the assembly backwards to insert the bottom pin into the drawbar. Secure the bottom pin with a hairpin. ASSEMBLY Support Assembly Hairpin 8063-086 8063-085 3MOUNTING BLOWER ASSEMBLY 1. Remove the discharge chute from the deck. 2. Lower deck to the lowest cutting position. 3. Remove the right hand (discharge side) belt cover from the deck. 4. Position blower over the discharge tabs on the deck and set blower onto the deck. 5. Be sure the blower is sitting flush against the outside of the deck. 6. Install the front mount bracket to the deck with the pin and hairpin cotter supplied with the kit. Rear Mount Bracket Contact Area 8063-072 Outer Pulley Cover Pin Hairpin Cotter 8063-073 1. Locate the rear adjustment nut on the discharge side of the deck. To assure the right tighteness, mark the front side of the nut. 2. Using the mark as a guide, turn the nut clockwise five turns with a ." wrench. 1DECK ADJUSTMENT 8 1. Make sure the tension release lever is forward (disengaged). 2. Place the belt over the pulley on the deck. Refer to illustration for proper routing. 3. Move the tension release arm to the rear and engage in the latch. 4INSTALLING DRIVE BELT Rear of Deck Idler Pulleys Outer Pulley Twist in Belt Tension Release Arm 8063-074 5INSTALLING BELT COVERS 1. Place the deck belt shield on the deck over the drive pulley and secure with hardware removed from steel belt shield. 2. Place retainer on the outer pulley cover. 3. Align the tab end of the belt cover into the slot on the deck belt shield and the other end over the end of the outer pulley cover. 4. Secure with knob. Retainer Outer Pulley Cover Deck Belt Shield Belt Cover Tab 8063-079 1. Position upper chute support against bagger inlet, flush at outer edges. See Illustration. 2. Using support as a template, drill two 3/8 holes into bagger hood. Bagger Inlet Flex Trim 3. Secure upper chute support to hood with hex bolts, washers and nyloc nuts. Use the illustration for hardware orientation. 4. Slide the flex trim over the support and bagger edge. 6INSTALLING CHUTE SUPPORT Upper Chute Support Upper Chute Support 8063-047 8063-048 ASSEMBLY 9 9INSTALLING CHUTES 1. Place middle chute over the top end of the blower assembly. Stretch the chute latch on the bl...