Log:
valutazioni - 3, GPA: 4 ( )

Istruzioni per l'uso Ryobi, Modello 280r

Produttore : Ryobi
File Size : 4.59 mb
File Nome : 6e474555-d4de-6044-85cc-5fcf0644790b.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Turn the lower vacuum tube clockwise until it snaps into detent and locks. (The dot on the lower tube aligns with the dot on the upper tube when properly assembled.) Lower Vac Tube Rg. 12- INSTALLING THE COMPLETE VACUUM TUBE ASSEMBLY TO THE BLOWER/VACUUM (MODEL 310BVr ONLY) WARNING: Do not install the vacuum tubes while unit is running to avoid serious personal injury. 1. Grasp the assembled vacuum tube firmly with both hands. Turn the tube/adapter clockwise as far as possible to the end of the grooves until it snaps into the detent and locks (Fig. 13). NOTE: When the tube is installed correctly, the flat on the upper tube faces the handle on the blower/vac (Fig. 13). Fig. 13 10 ASSEMBLY INSTRUCTIONS INSTALLING AND ADJUSTING THE SHOULDER STRAP (MODEL 310BVr ONLY) A WARNING: Always use the shoulder strap when using the vacuum (Model 31 OBVr only) to avoid serious personal injury. NOTE: Have the shoulder strap on and adjusted, but not clipped to the support fitting prior to starting unit. 1. Push the strap through the center of the buckle. 2. Pull the strap over the cross bar and down through the slot in the buckle (Fig. 14). 3. Fully extend the strap. 5. Place the strap over your head and onto your shoulders (Fig. 16). Fig. 16 6. While standing in the operating position (Fig.16) adjust length to fit the operator’s size. • Lengthen the strap by pulling down on the strap and lifting the buckle end up (Fig. 17). • Shorten the strap by pulling the strap down through the buckle while holding the buckle (Fig. 17). 4. Attach the metal clip of the shoulder strap to the support fitting on the back of the handle (Fig. 15). Lengthen Strap OIL AND FUEL INFORMATION OIL AND FUEL MIXING INSTRUCTIONS Old and/or improperly mixed fuel are the main reasons for the unit not running properly. Be sure to use fresh, clean unleaded fuel. Follow the instructions carefully for the proper fuel/oil mixture. Definition of Blended Fuels Today's fuels are often a blend of gasoline and oxygenates such as ethanol, methanol, or MTBE (ether). Alcohol-blended fuel absorbs water. As little as 1 % water in the fuel can make fuel and oil separate. It forms acids when stored. When using alcohol-blended fuel, use fresh fuel (less than 60 days old). Using Blended Fuels If you choose to use a blended fuel, or its use is unavoidable, follow recommended precautions. • Always use fresh fuel mix per your operator's manual. • Always agitate the fuel mix before fueling the unit. • Drain the tank and run the engine dry before storing the unit. Using Fuel Additives The bottle of Ryobi 2-Cycle Oil that came with your unit contains a fuel additive which will help inhibit corrosion and minimize the formation of gum deposits. It is recommended that you use only Ryobi 2-Cycle Oil with this unit. If unavailable, use a good 2-cycle oil designed for air-cooled engines along with a fuel additive, such as STA-BIL® Gas Stabilizer or an equivalent. Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel according to the instructions on the container. NEVER add fuel additives directly to the unit's fuel tank. CAUTION: For proper engine operation and A maximum reliability, pay strict attention to the oil and fuel mixing instructions on the 2-cycle oil container. Using improperly mixed fuel can severely damage the engine. Thoroughly mix the proper ratio of 2-cycle engine oil with unleaded gasoline in a separate fuel can. Use a 32:1 fuel/oil ratio. Do not mix them directly in the engine fuel tank. See the table below for specific gas and oil mixing ratios. NOTE: One gallon (3.8 liters) of unleaded gasoline mixed with one 4 oz. (120 ml.) bottle of Ryobi 2-Cycle Oil makes a 32:1 fuel/oil ratio. UNLEADED GAS RYOBI 2 CYCLE OIL 1 US. GALLON + 4.0 FL. OZ. (3.8 LITERS) (120 ml) 1 LITER + 30 ml MIXING RATIO - 32:1 A WARNING: Gasoline is extremely flammable. Ignited vapors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the area. A WARNING: Remove fuel cap slowly to avoid injury from fuel spray. Never operate the unit without the fuel cap securely in place. A WARNING: Add fuel in a clean, well-ventilated area outdoors. Wipe up any spilled fuel immediately. Avoid creating a source of ignition for spilled fuel. Do not start the engine until fuel vapors dissipate. NOTE: Dispose of the old fuel/oil mix in accordance to Federal, state, and local regulations. 12 STARTING/STOPPING INSTRUCTIONS STARTING INSTRUCTIONS A WARNING: Operate this unit only in a well-ventilated area outdoors. Carbon monoxide exhaust fumes can be lethal in a confined area. A ___ ?-- WARNING: Avoid accidental starting. Be in the starting position when pulling the starter rope (Fig. 20 for blower, Fig. 21 for vacuum). The operator and unit must be in a stable position while starting to avoid serious personal injury. Also, do not set unit o...

Questo manuale è adatto anche per i modelli :
Sistemi di ventilazione - 310BVr (4.59 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie