valutazioni - 4, GPA: 4.8
(
)
)
|
Facilità d'uso
off power unit. 3. Clean filters and grease-laden surfaces frequently. 4. Do not repair or replace any part of this appliance unless specifically recommended in this manual. All other servicing should be done by a qualified technician. 5. Please read specification label on product for further information and requirements. PLANNING INSTALLER: Save this manual for Electrical Inspector and Homeowner to use. HOMEOWNER: Use and Care Information on Page 5. AIR VENT COUNTER TOP BLOWER BOX CHIMNEY TOP 3-1/4" X 10" DUCT CONNECTOR COOK TOP GEAR MOTOR COVER TYPICAL INSTALLATION 120 VAC GROUNDED OUTLET This downdraft blower system is designed to be used to exhaust airborne contaminants when cooking with a variety of gas or electric cooktops. It can be mounted in island, peninsula, or conventional wall locations. This unit can be easily installed following these basic steps: • Cut out the countertop opening. • Mount the unit in the cabinet. • Connect the ductwork and electrical. • Install the cooktop. PLANNING -(continued) Note: The high level of air flow of this appliance may affect the gas flame on some types of gas cooktops. This is NORMAL and will cause no harm, but can be corrected by lowering the speed of the blower. SPECIFICATIONS VOLTS AMPS CFM DUCT 120 4.0 500 3-1/4 X 10 TAKE MEASUREMENTS 1. Refer to the cooktop installation instructions for dimensions of cooktop, countertop cut-out, and cabinet requirements. The Model PL30DD will fit in most 30" wide cabinets and the Model PL36DD will fit in most 36" wide cabinets. However, it is recommended that oversized cabinets be used for easier installation. 2. Cooktop depth can vary greatly from one to another. This may cause the fit of these two appliances to be rather tight. Pay special attention to the areas of potential interference highlighted above. A countertop with (A) a raised lip and/or (B) a backsplash may not allow enough flat countertop for a proper installation. Note that 2" of flat countertop is required behind cooktop and that 1-3/4" is necessary between the back edge of the cooktop and the inside of cabinet back. PLAN THE DUCTWORK RIGHT DISCHARGE LEFT DISCHARGE DOWN DISCHARGE (as shipped) 1. This downdraft blower system is designed for use with 3-1/4" x 10" ductwork (can be transitioned to 6" round). Three different discharge directions are available with side-to-side adjustment for accurate alignment of ductwork. 2. For best performance: Choose the ducting option which allows the shortest length of ductwork and a minimum number of elbows and transitions. Check location of floor joists, wall studs, electrical wiring or plumbing for possible interference. NOTE: The unit is shipped with the 3-1/4" x 10" discharge facing DOWN. See “CHANGING BLOWER DIRECTION” on page 3, if necessary. EQUALS 6 FT. OF STRAIGHT DUCT 6" ROUND ELBOW 3-1/4" X 10" TO 6" RD. TRANSITION 3-1/4" X 10" 90O ELBOW EQUALS 8 FT. OF STRAIGHT DUCT EQUALS 2 FT. OF STRAIGHT DUCT 3. The system will operate most efficiently when the ductwork does not exceed 40 feet of equivalent duct. The chart, above, shows equivalent feet of elbows and transitions. The number of feet of straight duct plus the equivalent feet of transitions and/or elbows to be used should equal 40 feet or less. NOTE: The equivalent feet of various roof and wall caps hasbeen taken into consideration. Do not include them in this calculation. PLAN THE WIRING 1. The downdraft blower system draws 4 AMPS and requires a 120 VAC, 60 Hz circuit. 2. The unit has a 2 ft. long power cord with a 3-pronged plug. Plan to provide a grounded outlet in a location which will allow the unit’s power cord to reach. (Note: If the Model PL30DD is being installed in a 30" wide cabinet or the Model PL36DD is being installed in a 36" wide cabinet, the outlet cannot be located on the back wall of cabinet.) Outlet may also be wall-mounted, with access hole in cabinet. 2 PREPARATION CHANGING BLOWER DISCHARGE (Optional) The blower is shipped with its discharge facing DOWN. Follow these steps ONLY if: • the position of the blower discharge needs to be moved so ductwork does not interfere with floor joists, plumb ing or wiring below. • it is necessary to rotate the blower discharge to the RIGHT or LEFT. Place the unit on its back on a table or work surface. DOWN DISCHARGE - MOVING BLOWER LEFT OR RIGHT SHEET CLAMP CHANNEL NUTS METAL SCREW BOTTOM FLANGE BLOWER 1.Loosen the 4 nuts and 2 clamp channels. 2.Slide blower to desired position. 3.Use supplied cover plate to close open space (if any). 4.Tighten wing nuts to secure top of blower and use sheet metal screws through bottom flange to secure bottom of blower. LEFT OR RIGHT DISCHARGE COVER PLATE CLAMP CHANNEL NUT BLOWER MOTOR PLUG SHEET METAL SCREW 1. Remove the 4 nuts and 2 clamp channels. CUT COUNTERTOP OPENING 1. Lay out and cut the cooktop cut-out far enough FORWARD so downdraft will fit behind it. 2. Set cooktop in place and slide it as far forward as possible. Center and square it with edges of countertop...
Questo manuale è adatto anche per i modelli :Sistemi di ventilazione - PL36DD (190.87 kb)