valutazioni - , GPA: ( )

Istruzioni per l'uso MTD, Modello 24695A

Produttore : MTD
File Size : 1.17 mb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Also keep throttle control lever in the stop position. 9. If the power leaf blower should become blocked with debris at any point, shut engine off and wait until the impeller comes to a complete stop before attempting to remove the obstruction. Disconnect spark plug wire to prevent accidental starting. 10. Check all bolts for tightness at frequent periods. 11. Never store this power leaf blower with fuel in the tank. Allow engine to cool before starting in any enclosure. 12. Keep equipment free of debris when not in use. 13. Never operate this leaf blower unless impeller guard and guard assembly are properly affixed in their place. 14. Never change inlet nozzle or auxiliary hose attachment when engine is running. 15. The manufacturer recommends that the operator wear safety glasses or some other suitable eye protection when operating this machine. 16. Exercise caution whenever operating leaf blower. Do Not allow exaust to be pointed in the direction of persons. I ASSEMBLY INSTRUCTIONS CONTENTS OF HARDWARE PACK: (See Figure 1.) A (2) Carriage Bolts B (2) Hand Knobs C (1) Hex Sems Bolt FIGURE 1. PARTS IN CARTON (See Figure 2): D(1) Upper Handle E(1) Directional Discharge ■I^NOTE The right and left side of your leaf blower is determined from operator's position. 1. Remove the leaf blower, hardware pack and all literature from the carton before discarding carton. 2. Figure 3 shows lower handle. Upper handle mounts in center hole only. FIGURE 3. 4 CARRIAGE BOLT (A) Place the upper handle (D) over the lower handle, lining up the holes. Secure with carriage bolts (A) and hand knobs (B). See figure 4. FIGURE 4. DIRECTIONAL DISCHARGE (E) 4. Slip end of directional discharge (E) over chute opening. Secure in position with hex sems bolt (C). See figure 5. FIGURE 5. OPERATION BEFORE STARTING ENGINE Service engine with gas and oil. See engine manual packed with leaf blower for complete instructions care and maintenance of engine. READ DIRECTIONS CAREFULLY. TO START ENGINE 1. Move throttle to start position. 2. Pull starter rope once with quick, full stroke. Move hand throttle to fast position and pull starter rope again. 3. When engine starts, move throttle to "RUN" position until engine warms up. TO STOP ENGINE Move throttle control lever to "OFF" position. ADJUSTMENTS t WARNING J Do Not make this adjustment or any adjustment with the engine running. Stop the engine, disconnect the spark plug wire and ground plug wire to engine block. FIGURE 7. TWO-WAY AIR DISCHARGE Your leaf blower is equipped with an adjustable chute deflector. Simply push down on handle provided and swing door towards the front or side as desired. See figure 6. ,.'r HANDLE DIRECTIONAL DISCHARGE FIGURE 6. HEIGHT ADJUSTMENT To adjust the height of the discharge, stand on the right hand side of the leaf blower and move the index handle towards the engine. Move handle towards rear of unit to lower height. Move the handle forward to raise the height. See figure 7. MAINTENANCE AND LUBRICATION Your leaf blower, like all machines with moving parts, must receive care and maintenance. The following tips, if used, will contribute many troublefree hours to your blower. 1. Check oil level frequently. When changing oil, make sure dirt and debris is cleaned off oil sump before removing oil plug. 2. Keep blower clean, especially the engine, and engine air filter. 3. Check all nuts, bolts and screws occasionally to be sure blower is in good operating condition. 4. The wheel bearings are pre-lubricated at the factory and should require no further attention until blower is serviced. However, it is advisable to remove the wheels and apply a small amount of light oil to each axle at least once a season. OFF-SEASON STORAGE If you are going to store your blower for any length of time (30 days or longer), it is important that the following steps be taken: 1. Drain the gas tank. Start the engine. Allow it to run out of gas. Gasoline left in the engine will leave gum deposits in the carburetor and gas tank. Clean engine of all foreign matter. 2. 3. Lubricate cylinder by removing the spark plug and pour in one ounce of clea...