valutazioni - 2, GPA: 4 ( )

Produttore : Dixon File Size : 1.6 mb File Nome : XOUS2007_539132264R1.pdf Lingua di insegnamento:

• Never carry children. They may fall off and be seriously injured or interfere with safe machine operation. • Keep children out of the mowing area and under the watchful care of another responsible adult. • Be alert and turn machine off if children enter the area. • Before and when backing, look behind and down for small children. • Mow up and down slopes (10° Max), not across. • Remove obstacles such as rocks, tree limbs, etc. • Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles. • Use a slow speed while on slope or hill. • Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. • If machine stops while going uphill, disengage blades, shift into reverse and back down slowly. • Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. CAUTION Look for this symbol to point out important safety precautions. It means CAUTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. CAUTION In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark WARNING Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARNING Battery posts, terminals and related accessories contain lead and lead compounds, chemicals know to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. 7 UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton. TOOLS REQUIRED • Drill and 11/32" drill bit - 3 bag system only • 5/16" Wrench or ratchet and socket • 7/16" Wrench or ratchet and socket • ." Wrench or ratchet and socket • ." Socket • Torque Wrench • Phillips Head Screwdriver • Pliers NOTE: When right hand (RH) and left hand (LH.) are mentioned in this manual, it means when seated on the mower in the operator’s position. CAUTION BEFORE ASSEMBLING GRASS CATCHER TO MOWER: • Set parking brake. • Place motion control levers in “NEUTRAL” position. • Turn ignition key “OFF” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug and place wire where it cannot come in contact with plug. UPPER CHUTE BAG DUMP INDICATOR BLOWER HOUSING MIDDLE CHUTE CONTAINER CONTENTS • Blower Assembly • Drive Pulley • Belt Shield • Belt • Mounting Assembly • Bag of Hardware • Weight (not included in 50" Kit 539 132397 or 60" Kit 539 132252) BELT COVER 8 ASSEMBLY 1. Remove the discharge chute from the deck. (Deck confi guration will vary by size and model) 2. Lower deck to the lowest cutting position. 3. Remove the right hand (discharge side) belt cover from the deck. 4. Relieve the tension from the deck belt and remove from the center deck pulley. (See Operator’s Manual if necessary) 1INSTALLING DRIVE PULLEY DISCHARGE CHUTE BELT COVER DECK HEIGHT ADJUSTMENT 5. Remove the bolt that secures the right hand deck pulley to the spindle. 6. Replace right blade shaft with new, longer shaft. The existing drive pulley and key will fi t on the new shaft. Install blower drive pulley with the raised portion of pulley hub down. Slide spacer inside new pulley. Add key to new pulley. 7. Remove two rear bolts from spindle and place belt shield standoff where the two bolts were removed. Replace bolts and tighten. 8. Use heavy washer and bolt supplied in kit to attach pulley to spindle. Torque to 55-75 ft/lbs. 9. Reinstall the deck belt. DRIVE PULLEY KEY REPLACEMENT SHAFT BELT SHIELD STANDOFF SPINDLE NEW HEAVY WASHER NEW BOLT SPACER 9 ASSEMBLY 2MOUNTING BLOWER ASSEMBLY OUTER PULLEY COVER PIN HAIRPIN COTTER 3INSTALLING DRIVE BELT REAR OF DECK IDLER PULLEYS OUTER PULLEY TWIST IN BELT TENSION RELEASE LEVER 1. Install the front and rear mount brackets to the deck with the pin and hairpin cotter supplied with the kit. 1. Make sure the tension release lever is forward or disengaged. 2. Place the belt over the pulley on the deck. Refer to illustration for proper routing. 3. Move the tension release lever to the rear and engage in the latch. 10 ASSEMBLY BELT COVER TAB 4 INSTALLING BELT COVERS RETAINER KNOB OUTER PULLEY COVER DECK BELT SHIELD MIDDLE CHUTE LATCH DECK BELT SHIELD WING NUT TAP SCREW BELT SHIELD STANDOFF 1. Place deck belt shield over spindle, aligning hole with bolt on belt shield standoff. 2. Attach with wing nut to standoff and use tap screw from kit to attach the other side of the belt shield to the deck. 3. Place retainer on the outer pulley cover. 4. Align the tab end of the belt cover into the slot on the deck belt shield and the other end over the end of the outer pulley cover. 5. Secure with knob. 11 ASSEMBLY 5INSTALLING MIDDLE CHUTE MIDDLE CHUTE BLOWER ASSEMBLY Depending on model, engine guard may have available mounting holes. If drilli...

Scarica la tua

Per scaricare, digitare 2 cifre :