Log:
Scaricare : 0   File Size : 988 kb   Produttore : Lennox Hearth  
Categoria : Sistemi di ventilazione
@name

Blower Wire Harness (item #1) 1 ea. Snap Switch and Control Panel Housings (item #2) 1 ea. 6” of 3/4” Heat Shrink Tube (item #3) 2 ea. Butt Connectors (item #4) 3 ea. Wire Ties (item #5) 1 ea. Instruction Sheet TOOLS NEEDED 5/32 Allen Wrench Or T Handle Wrench Cutting Pliers Wire Crimpers 9/16” Socket Wrench 9/16” Open End Wrench Crescent Wrench 3/8” End Wrench Large Flat Head Screwdriver 4 2 3 5 Figure 1 - Kit Contents GENERAL INFORMATION This retrofit kit works in conjunction with the optional

Scaricare : 0   File Size : 605 kb   Produttore : Lennox Hearth  
Categoria : Sistemi di ventilazione
@name

See Figure 5. Snap switch Bracket Tabs Figure 5 Step 4. While holding the snap switch bracket against the pedestal, slide the bracket towards the rear of the stove until it comes to a stop. Once the snap switch bracket is in place you can then remove the flat head screwdriveror pry bar that was used to create theopening between the firebox bottom and pedestal. See Figure 6. Snap switch housing Figure 6 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Step 5. With the snap switch bracket in place

Scaricare : 3   File Size : 231 kb   Produttore : Lennox Hearth  
Categoria : Sistemi di ventilazione
@name

H0767) FOR MODELS – CI1500 AND CI2500 SERIES KIT CONTENTS: 1 ea. Blower Assembly 1 ea. Rheostat Assembly 1 ea. Fan Disc with 1 ea. White Wire 5 ea. Screws, #8 x .” 1 ea. Instruction Sheet TOOLS REQUIRED: 1/4” & 7/16” Nut Drivers or Sockets INSTALLATION INSTRUCTIONS: 1. The following instructions, 1 through 11 are for units WITHOUT an Optional Full Function Flame Modulating Remote Control System, H0301 or H0302. If either of these kits have been purchased, follow instructions on Page 2 instead –

Scaricare : 0   File Size : 250 kb   Produttore : Lennox Hearth  
Categoria : Sistemi di ventilazione
@name

H4678) FOR USE WITH ELDV SERIES FIREPLACES GENERAL INFORMATION This blower kit may be used with ELDV series fireplaces. The LBLK100 blower kit is used with a field supplied ON/OFF power switch. The blower is installed beneath the firebox. Room air is drawn in through the bottom area of the fireplace, heated as it passes across the firebox, and discharged through the upper open area at the top of the fireplace. The LBLK-100 blower kit contains one blower, one power cord and these instructions. IN

Scaricare : 0   File Size : 2 mb   Produttore : Lennox Hearth  
Categoria : Sistemi di ventilazione
@name

75194 INSTALLATION INSTRUCTIONS FOR an AIR CIRCULATION BLOWER KIT for use wit h the VINTAGE™ 27 GAS STOVE 775202M Rev. A, 01/2011 LENNOX HEARTH PRODUCTS KITS AND ACCESSORIES KIT CONTENTS 1 ea. Blower Assembly (item #1) 2 ea. Washers, #10 (item #2) 2 ea. Nuts, 10-24 Nylock (item #3) 1 ea. Instruction Sheet NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE TURN OFF THE STOVE AND ALLOW IT TO COMPLETELY COOL BEFORE PROCEEDING. Installation Instructions Step 1. Using an allen wrench, remove socket head





categorie