Experiment until you find the best position for your needs. For best performance, be sure engine recoil starter assembly, the blower intake and outlet areas are always kept clear and free of leaves or other debris. Maintenance Instructions Keep all nuts, bolts, and screws tight. Never store the blower with fuel in its fuel tank inside a building or in a confined space where fumes may reach an open flame or sparks. Always refer to the instruction manual for important details if the product is to

– Do not blow towards people, cars, windows, or other items which could be injured or damaged by the blown debris. – Keep hands away from the blower air intake and outlet. STARTING – Start according to instructions in this manual or on the machine. – Do not change engine governor settings or overspeed the engine. Operating the engine at excessive speed can increase the hazard of personal injury. INTERRUPTING OPERATION - Before leaving the operator's position: - Park on level ground. - Shut off t

• Provide all operators of this equipment with the Operator's Manual and instructions for safe operation. • Do not point blower at people or animals. • Start unit on ground with throttle at idle. Check that blower pipe is not blocked by the ground or by any objects. WARNING DANGER Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Keep A Firm Grip • Hold handle with fingers together encirclin

Do not allow the rope to snap back in. Always hold the unit firmly. • (PB-770H): Rotate spring loaded throttle arm downward to a comfortable operating position. - PB-770 H 1. Throttle Lever Move throttle position lever (A) to IDLE DETENT positions. - PB-770 T 1. Throttle Position / Stop Switch Button Slide Throttle Position / Stop Switch Button (A) back to idle position. - PB-770 H and T 2. Choke Move choke (C) up to Cold Start Position ( ) 3. Purge Bulb Pump purge bulb (D) until fuel is visible

4. Use a tachometer to adjust idle speed to specifications found on page 11. 22 TROUBLESHOOTING Problem Cause Remedy Engine - starts hard Engine - does not start Engine Cranks Fuel at carburetor No fuel at carburetor Fuel strainer clogged Fuel line clogged Carburetor Clean Clean See your ECHO dealer Fuel at cylinder No fuel at cylinder Carburetor See your ECHO dealer Muffler wet with fuel Fuel Mixture is too rich Open choke Clean/replace air filter Adjust carburetor See your ECHO dealer Spark at

7. Remove the spark plug and pour 7cc (1/4 oz., 1/2 tablespoon) of fresh, clean ECHO 2-stroke engine oil into the cylinder through the spark plug hole. A. Place a clean cloth over the spark plug hole. B. Pull the recoil starter handle 2-3 times to distribute the oil inside the engine. C. Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston reaches the top of its travel and leave it there. 8. Install the spark plug (do not connect ignition cable)

Any Little Wonder Gasoline powered Maximum Output Blower or part found to be defective within the warranty period is to be returned to any registered Little Wonder dealer. Engines for all gasoline powered products are warranted separately by the engine manufacture. Therefore, there are no warranties made, expressed or implied, for engines for gasoline powered products by Little Wonder. Transportation charges for parts and units submitted for replacement under this warranty must be borne by the p

As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from sparks and flames. IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use. SM T W T F S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 31 30 14 OPERATION -Provide all

3. Clean cylinder fins (A) to allow cooling air to pass freely. 4. Replace cover and tighten screws. 5. Connect spark plug lead. A EXHAUST SYSTEM Spark Arrestor Screen Level 2. Tools required: Cross Head Screwdriver Parts Required: Spark arrestor screen P/N 14586206720, Gasket P/N V104000220 IMPORTANT Carbon deposits in muffler will cause a drop in engine output and overheating. Spark arrestor screen must be checked periodically. 1. Remove spark plug and engine cover (five screws). 2. Remove spa

Pay particular attention to all sections regarding safety. Store your owners manual in a safe place. Warnings - “Don’ts” DANGER ROTATING FAN - KEEP HANDS AWAY. DON’T ATTEMPT TO REMOVE MATERIALS FROM INTAKE OR DISCHARGE WHEN BLOWER IS RUNNING KEEP CHILDREN, PETS, AND BYSTANDERS AWAY - DO NOT PERMIT CHILDREN TO CONTACT BLOWER. KEEP CHILDREN A SAFE DISTANCE FROM WORK AREA. NEVER ALLOW A PERSON MENTALLY ILL, UNDER INFLUENCE OF ALCOHOLIC DRINKS OR DRUGS OR TOO YOUNG IN AGE, TO OPERATE THE BLOWER DANG