valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
There are 4 slots (dia. 8.5 mm) on the sides of the scanner for mounting. The diagram below can be used for installation; refer to the Reading Diagrams for correct positioning of the scanner with respect to the reading zone and scanner orientation. 470 [18.50] 300 [11.81] = = 180 [7.09] 22 [0.87] 406 [15.98] 22 [0.87] 8.5 [0.33] 141 [5.55] 147 [5.79] 10 [0.39] 370 [14.57] = = 370 [14.57] = = = = 60.5 [2.38] 70.5 [2.78] N° 4 DX8200A-3002 Overall Dimensions Scanner Direction The different scanner orientations are illustrated in the following figures: DX8200A-3002 Scanner Direction 0° (Forward) DX8200A-3002 Scanner Direction 180° (Reverse) PackTrack™ Coordinate Reference Point where x, y, z = 0 Top View Conveyor Direction Top View Conveyor Direction E Reading Diagrams: Note: x = 0 and z = 0 correspond to the edge of the DX8200A-3002 scanner as shown in the figure below. DX8200A-3002 (0.50 mm/20 mils) 0 -15 -24 -32 0 -40 -60 -80 z x CONDITIONS Code = Interleaved 2/5 or Code 39 PCS = 0.90 Compliance: Laser Safety -28 -24 -20 -16 -12 -8 -4 0 4 8 12 16 20 24 28 (in) -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 (cm) (in) -100 -120 -140 -160 (cm) -40 -48 -56 -64 1 1 Figure A Figure B 1 Warning and Device Class Label 1 Device Identification Label The scanner is classified as a Class 2 laser product according to EN60825-1 regulations and as a Class II laser product according to CDRH regulations. Disconnect the power supply when opening the device during maintenance or installation to avoid exposure to hazardous laser light. There is a safety device, which allows the laser to be switched on only if the motor is rotating above the threshold for its correct scanning speed. DX8200A-3002 QUICK GUIDE 10 The laser beam can be switched off through a software command (see also the Genius™ Help On-Line). LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT MAXIMUM OUTPUT RADIATION 1 mW EMITTED WAVELENGTH 630~680 nm TO EN 60825-1:2001 CAUTION-CLASS 3B LASER LIGHT WHEN OPEN AVOID EXPOSURE TO BEAM LASER LIGHT EMITTED FROM THIS APERTURE Warning and Device Class Label Model No. Amp. Serial No. DATALOGIC S.P.A. Via Candini, 2 40012 Calderara di Reno - Bologna - Italy Manufactured Volt This product conforms to the applicable requirements of 21CFR1040 at the date of manufacture. Device Identification Label The laser diodes used in this device are classified as Class 3B laser products according to EN 60825-1 regulations and as Class IIIb laser products according to CDRH regulations. As it is not possible to apply a classification label on the laser diodes used in this device, the following label is reproduced here: LASER LIGHT AVOID EXPOSURE TO BEAM CLASS 3B LASER PRODUCT MAXIMUM OUTPUT RADIATION 30 mW EMITTED WAVELENGTH 630~680 nm TO EN 60825-1 (2001) Laser Diode Class Label Any violation of the optic parts in particular can cause radiation up to the maximum level of the laser diode (30 mW at 630~680 nm). Power Supply This product is intended to be installed by Qualified Personnel only. - This scanner is intended to be supplied by either a UL Listed power supply marked 'Class 2' or 'LPS', output rated 20 - 30 V dc, minimum 1.75 A or by a UL Listed computer with LPS outputs. - This scanner must be supplied by a Class II Power Supply Unit conforming to the EN 60950 safety regulation. WEEE Compliance DATALOGIC S.p.A. , Via Candini, 2 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the declare que le bescheinigt, da. das Gerat declare que el DX8200A-XXXX, Laser Scanner e tutti i suoi modelli and all its models et tous ses modeles und seine Modelle y todos sus modelos sono conformi alle Direttive del Consiglio Europeo sottoelencate: are in conformity with the requirements of the European Council Directives listed below: sont conformes aux specifications des Directives de l'Union Europeenne ci-dessous: den nachstehenden angefuhrten Direktiven des Europaischen Rats: cumple con los requisitos de las Directivas del Consejo Europeo, segun la lista siguiente: 89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi and further amendments et ses successifs amendements und spateren Abanderungen y succesivas enmiendas 73/23/EEC Low Voltage Directive Basate sulle legislazioni degli Stati membri in relazione alla compatibilita elettromagnetica ed alla sicurezza dei prodotti. On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety. Basee sur la legislation des Etats membres relative a la compatibilite electromagnetique et a la securite des produits. Uber die Annaherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Vertraglichkeit und Produktsicherheit entsprechen. Basado en la aproximacion de las leyes de los Paises Miembros respecto a la compatibilidad electromagnetica y las Medidas de seguridad relativas al producto. Questa dichiarazione e basata sulla conformita dei prodotti alle norme seguenti: This declaration is based upon compl...