valutazioni - 2, GPA: 3
(
)
)
|
Facilità d'uso
Please refer to page 47 “Specifications” for details. • For documents up to A4, letter or legal size, up to 300 sheets of 64 g/m2 (17 lbs.) paper can be placed at one time on the hopper. For documents up to B4, A3 or ledger size, up to 200 sheets of 64 g/m2 (17 lbs.) paper can be placed. • Even with A4, letter and legal size documents, the maximum number of sheets of paper which can be inserted when the documents are to be scanned in the landscape mode is 200 which is the same number as for the B4, A3 and ledger size documents. (This is the number of sheets that comes up to the B4-A3 limit mark.) 5 Adjust the document guides to the size of the document to be scanned. Adjust the exit document guides to the size of the document to be output, if required. A4, LTR B4TA3 Fill indicator (Limit mark) The fill indicator illustration is only for the KV-S2065W. Portrait A Document guide Exit document guide A Landscape Loading Documents 6 When using long paper, pull out the hopper extension tray from the hopper and the exit stopper from the exit extension tray. You can also extend the exit extension tray, if required. (See fig. 1) • When scanning narrow documents as shown below, pull up the exit substopper. (See fig. 2) Scanning direction tray Document • When scanning thin documents, raise the exit substopper slightly to let the document exit smoothly. (See fig. 3) Exit extension tray Exit stopper Hopper extension Fig. 1 Exit substopper Fig. 2 Fig. 3 Exit substopper Cautions: • For thin, thick or important paper, scan the document using single sheet (manual feed) mode. Also, remove the document from the pre-imprinter door (exit part) after it is scanned. • The scanner will accept 50 to 157 g/m2 (13 to 42 lbs.) paper for continuous scanning and 20 to 157 g/m2 (5.3 to 42 lbs.) paper for single scanning. • When scanning a thin, folded, creased or curled document, after straightening the document, set the feed speed to “Slow”. • When scanning thin documents, be sure to use less than 300 sheets. • When scanning copying paper such as carbon or carbonless paper, set hopper single sheet (manual feed). • When setting the document, be sure that it does not exceed the fill indicator (limit mark). • Be sure to remove the document from the pre-imprinter door (exit part) after it is scanned. • In cases where very fragile documents are to be scanned, it is recommended to make a copy and scan the copy. Types of documents to avoid: • OHP sheets, other plastic film, cloth, or metallic sheets • Paper with irregularities such as tabs, staples, paste, etc. • Documents with wet ink • Thick or irregular documents such as envelopes, paste, etc. • Copying paper such as carbons. • Damaged or wrinkled documents • Irregular shaped documents • Tracing paper Secondary Settings . ....Selecting the paper path for scanned document To select the front, set the paper path selector to the upper side. To select a straight path pass through to the back, set the paper path selector to the lower side. • When scanning documents with a thickness of 0.2 mm to 1 mm, like folded documents, set the paper path selector to straight. Paper path selector The paper path selector is located on the left side of the scanner. ....Setting the ADF / manual feed selector . Single scanning When scanning a single sheet or several sheets, set the ADF / manual feed selector to “MANUAL”. . Continuous scanning When scanning normal paper continuously, set the ADF / manual feed selector to “2”. When scanning with smooth sided paper or a paper jam occurs with normal paper, set the ADF / manual feed selector to “3”. When double feeding occurs frequently or scanning a document with a rough face as in NCR paper, set the ADF / manual feed selector to “1”. When a jam occurs at the paper feed component, set the ADF / manual feed selector to “4”. • The ADF / manual feed selector must be set in the chosen specific position for this setting to function properly. • If double feed alarm beeps frequently, change the ADF / manual feed selector. 2 1 3 4 ADF ADJ. ADF / manual feed selector MANUAL The ADF / manual feed selector is located on the left side of the scanner. Others . ....How to use the control sheet If the control sheet is used, the documents under the control sheet are scanned in accordance with the code on the control sheet regardless of scanning condition that is selected previously. • Multiple control sheets can be used. • When using a control sheet, the application software required depends on the control sheet. • Print out control sheets from the provided CDROM. Caution • Use the same size control sheet as the scanning document. • When printing the control sheet, if the pattern falls in the area from the top side of the document to 25 mm, adjust the printer. Also, copy the control sheet so that the pattern lies in the center of the copy. • Be careful not to get the control sheet dirty. Do not fold or crease the control sheet. Scanning will not be performed properly. Code Documents...