valutazioni - 5, GPA: 4.4
(
)
)
|
Foto e specifiche Canon CanoScan 8600F |
Facilità d'uso
• Align the Film Guide’s tab with the FILM symbol on the document glass of the scanner. Film Holder Calibration Slot • Place a black piece of paper over any gap to shield the light if you are inserting a film strip with 5 or fewer frames, or if the edge of a scanned image appears whitened. • Ensure that there is no gap between the edge of the film and the film guide on the side near the calibration slot. 6 Scanning Film 7 English 35mm Slides .. Align the Film Guide’s tab with the FILM symbol on the document glass of the scanner. .. Place a slide or slides face down (correctly viewed from below) in the Film Guide as shown in the diagram to the right. 120 Format Films .. Open the film holder on the film guide, place the film face down and close the film holder. .. Align the Film Guide’s tab with the FILM symbol on the document glass of the scanner. 3 Close the document cover. • Leave a gap of 5 mm or greater between film strips when placing two or more on the document glass. • Ensure that there is no gap between the edge of the film and the film guide on the side near the calibration slot. Using a Film Retainer Sheet Curled film strips can stick to the document glass and cause a pattern of rings called Newton Rings to appear on the scanned image. If this occurs, scan using the supplied film retainer sheet as shown in the diagram. (A) Scan with the film retainer sheet inserted beneath the film. (B) If Newton Rings still appear after following Instruction (A), turn the film strip over and place it in the film holder with the film retainer sheet on top so that the film edges are held down for scanning. Then preview the image in ScanGear and click the [Mirror] button to reverse the image before initiating the final scan. To avoid damaging the film, always place the glossy side (the side without an illustration) of the film retainer sheet against the film. (A) Film Holder 120 Format Film Film retainer sheet With its glossy side facing upward, slip the film retainer sheet under the film. (B) Hold the film edges down by placing the film retainer sheet on top with its glossy side facing downward. Scanning Film 4 Start ArcSoft PhotoStudio, then start ScanGear. Follow the steps 2 to 4 in "Try Scanning" on page 4. 5 Select [Negative Film (Color)] or [Positive Film (Color)] in [Select Source] to match the type of film you are scanning, then click [Preview]. 6 Place a check mark beside the number(s) of the frame(s) you want to scan. Perform image corrections as needed. 7 Click [Scan] to start scanning. Do not touch the scanner while it is operating. 8 When prompted to close ScanGear, click [OK]. 9 Save the scanned image in ArcSoft PhotoStudio and close the window. • Do not leave the film strip in the film guide for an extended period of time as heat from the unit may damage the film. • For more information on scanning film, see “Scanning Film” in the Scanning Guide. 8 Specifications Specifications English CanoScan 8600F Scanner Type Flatbed Scanning Element CCD 6-line color Light Source Cold cathode fluorescent lamp Optical Resolution *1 4800 x 9600 dpi Selectable Resolution 25–19200 dpi (ScanGear) Scanning Bit Depth Color 48 bit input (16 bit for each color) 48 bit or 24 bit output (16 bit or 8 bit for each color) Grayscale 48 bit input (16 bit for each color) 16 bit *2 or 8 bit output Scanning Speed *3 (Photo or Document) Color 6.9 msec./line (2400 dpi), 13.8 msec./line (4800 dpi) Grayscale, B&W 6.9 msec./line (2400 dpi), 13.8 msec./line (4800 dpi) Scanning Speed *3 (Film) 6.8–67.5 msec./line Preview Speed *3*4 Approximately 4 sec. Interface USB 2.0 Hi-Speed Maximum Document Size A4/Letter: 216 x 297 mm Film Type/Number of Frames 35 mm strip (12 frames max)/35 mm slide (4 frames max) 120 format film: max. 6 x 22 cm (filmstrip only) Scanner Buttons 7 buttons (PDF x 4, COPY, PHOTO/FILM, E-MAIL) Operating Range Temperature 10..C to 35..C (50..F to 95..F) Humidity 10% to 90% RH, 20% to 80% RH for film scanning without condensation formation Power Requirements AC adapter (100/120/230/240V) *5 Power Consumption In operation: 18 W maximum, Stand-by: 5 W, Switch-off: 0.5 W (Using supplied AC adapter) Maximum Exterior Dimensions 283 x 467 x 120 mm Weight Approximately 4.3 kg *1 Optical Resolution represents the maximum sampling rate based on ISO 14473. *2 For film scanning only. *3 The fastest speed in USB 2.0 Hi-Speed mode on Windows PC. Transfer time is not included. Scanning speed varies according to the document types, scan settings, or specifications of the computer. *4 Calibration processing time is not included. *5 AC adapter type varies according to the region in which the scanner is purchased. Use only AC adapters listed in the user instructions. (Canon AC Adapter: K30279 is for United Kingdom and K30278 is for other EU countries). Do not use them for other products. • Specifications are subject to change without notice. Model Number: K10294 (CanoScan 8600F) 9 European Union (and EEA) only. This symbol indicates that th...