valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
scanner / copiatrice / MFP - MFC-9320CW (15.47 mb)
Facilità d'uso
Check the following: • Envelopes should have a lengthwise sealing flap. • The sealing flaps should be folded crisply and correctly (irregularly cut or folded envelopes may cause paper jams). • Envelopes should consist of two layers of paper in the area circled in the figure below. 11 1 Feeding direction • Envelope joints that are sealed by the manufacturer should be secure. • We recommend that you do not print within 0.6 in. (15 mm) of the edges of envelopes. Types of envelopes to avoid IMPORTANT DO NOT use envelopes: • that are damaged, curled, wrinkled or an unusual shape • that are extremely shiny or textured • with clasps, staples, snaps or tie strings • with self-adhesive closures • that are of a baggy construction • that are not sharply creased • that are embossed (have raised writing on them) • that were previously printed by a laser/LED machine • that are pre-printed on the inside • that cannot be arranged neatly when stacked • that are made of paper that weighs more than the paper weight specifications for the machine • with edges that are not straight or consistently square • with windows, holes, cut-outs or perforations • with glue on surface as shown in figure below • with double flaps as shown in figure below 2 21 Chapter 2 • with sealing flaps that have not been folded at purchase • with sealing flaps as shown in figure below • with each side folded as shown in figure below If you use any of the types of envelopes listed above, they may damage your machine. This damage may not be covered under any Brother warranty or service agreement. Occasionally you may experience paper feed problems caused by the thickness, size and flap shape of the envelopes you are using. Labels The machine will print on most types of labels designed for use with a laser machine. Labels should have an adhesive that is acrylic-based since this material is more stable at the high temperatures in the fuser unit. Adhesives should not come in contact with any part of the machine, because the label stock may stick to the drum unit or rollers and cause jams and print quality problems. No adhesive should be exposed between the labels. Labels should be arranged so that they cover the entire length and width of the sheet. Using labels with spaces may result in labels peeling off and causing serious jams or print problems. All labels used in this machine must be able to withstand a temperature of 392 degrees Fahrenheit (200 degrees centigrade) for a period of 0.1 seconds. Label sheets should not exceed the paper weight specifications described in this User’s Guide. Labels exceeding this specification may not feed or print properly and may cause damage to your machine. Labels must be fed from the manual feed slot only. Types of labels to avoid Do not use labels that are damaged, curled, wrinkled or an unusual shape. IMPORTANT Avoid feeding labels with the carrier sheet exposed because your machine will be damaged. 22 Loading documents Using the automatic document feeder (ADF) The ADF can hold up to 35 pages and feeds each sheet individually. Use standard 20 lb (80 g/m2) paper and always fan the pages before putting them in the ADF. Recommended environment Temperature: 68°F to 86°F (20°C to 30°C) Humidity: 50% - 70% Paper: Xerox 4200 (20 lb/Letter) IMPORTANT • DO NOT leave thick documents on the scanner glass. If you do this, the ADF may jam. • DO NOT use paper that is curled, wrinkled, folded, ripped, stapled, paper- clipped, pasted or taped. • DO NOT use cardboard, newspaper or fabric. • To avoid damaging your machine while using the ADF, DO NOT pull on the document while it is feeding. Note To scan documents that are not suitable for the ADF, see Using the scanner glass on page 24. • Make sure documents with correction fluid or written with ink are completely dry. • Documents to be faxed must be from 5.8 to 8.5 in. (147.3 to 215.9 mm) wide and from 5.8 to 14 in. (147.3 to 355.6 mm) long, and of a standard weight [20 lb (80 g/m2)]. Loading paper and documents a Unfold the ADF document output support flap (1) and the ADF support flap (2). 1 2 b Fan the pages well. c Place your document face up, top edge first in the ADF until the LCD display message changes and you feel it touch the feed rollers. d Adjust the paper guides (1) to fit the width of your document. 1 2 23 Chapter 2 c Close the document cover. Using the scanner glass You can use the scanner glass to fax, copy or scan pages of a book one page at a time. IMPORTANT If the document is a book or is thick do not Documents can be up to 8.5 in. wide and slam the cover or press on it. 11.7 in. long (215.9 mm wide and 297 mm long). Note To use the scanner glass, the ADF must be empty. a Lift the document cover. b Using the document guidelines on the left and top, place the document face down in the upper left corner of the scanner glass. 24 3 General Setup 3 General Setup Mode Timer The machine has three mode keys on the control panel: Fax, Scan, and Copy. You can set how much tim...
Questo manuale è adatto anche per i modelli :scanner / copiatrice / MFP - MFC-9120CN (15.01 mb)