valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
g Attach the original orange protective cover to each of the toner cartridges. Place each of the toner cartridges into the plastic bag that the cartridge originally came in. 1 144 h Hold the green parts of the belt unit with both hands and lift the belt unit up, then pull it out. CAUTION We recommend that you place the belt unit on a clean, flat surface with a piece of disposable paper underneath it in case you accidentally spill or scatter toner. i Remove the waste toner box from the machine using the green handle and place it into the plastic bag included in the carton. j Put the belt unit back in the machine. Match the h mark on the belt unit to the g mark on the machine. Push down on the green area of the belt unit to lock it in place. Troubleshooting and routine maintenance 145 C k Insert the original orange packing material for locking the belt unit as shown in the illustration. l Put a piece of paper (letter or A4) on the belt unit to prevent damage to the belt unit. m Put the drum unit back in the machine as follows. 1 Make sure that the gray lock lever (1) is in the up position and put the drum unit in the machine. Push down the gray lock lever (1). 1 1 146 Note When you put the drum unit in the machine, match the green guides (1) of the drum unit handle to the green arrows (2) on both sides of the machine. 2 Push the drum unit back in until it stops. n Insert the original orange packing material for the drum unit until as shown in the illustration, and then close the front cover. 2 1 2 1 Troubleshooting and routine maintenance 147 C o Note We recommend you repack the machine on a table or desk. Put the styrofoam piece marked “FRONT” (1) into the lower carton (3), so that the arrow cutout (4) points toward it. Put the styrofoam piece marked “REAR” into the lower carton so that the arrow cutout (4) points away from it. p Using two people, place the machine into the plastic bag and then into the lower carton, matching the “FRONT” piece to the front of the machine as shown in the illustration in Step o. q As shown in the illustration, fit the two foam pieces marked “FRONT” (4) to the cardboard piece marked “FRONT” (7). Fit the “REAR/L” (5) and “REAR/R” (6) foam pieces to the left and right of the cardboard piece marked “REAR” (8). r Put the assembled “FRONT” (1) and “REAR” (2) cardboard pieces in the lower carton at the front and rear of the machine as shown in the illustration. The foam pads should fit closely to the machine to support it. s Place the upper carton (1) over the machine and the lower carton. Match the joint holes (2) of the upper carton to the joint holes (3) of the lower carton. 3 2 1 4 4 8 7 6 5 1 2 2 1 148 t Put the two styrofoam pieces for the toner cartridges on the top of the machine. Match the right side of the machine to the “RIGHT” mark on one of the styrofoam pieces, and the left side of the machine to the “LEFT” mark on the other styrofoam piece. Put the toner cartridges in the styrofoam. u Put the carton tray (1) on the top. Match the front side of the machine to the marks on the carton tray. Place the waste toner box in the right side of the carton tray. v Put the four joints (1) into the holes of the carton using steps A and B as shown below. w Close the carton and tape it shut. 1 1 A B 1 Machine information Checking the serial number You can see the machine’s serial number on the LCD. a Press Menu, 6, 2. 62.Serial No. XXXXXXXXX b Press Stop/Exit. Checking the page counters You can see the machine’s page counters for printed pages, copies, reports and lists or a summary total. a Press Menu, 6, 3. The LCD shows the total number of pages for Total, List and Copy. 63.Page Counter a Total :XXXXXX List :XXXXXX b Copy :XXXXXX Select ab or OK b Press a or b to see number of pages for Print. 63.Page Counter a List :XXXXXX Copy :XXXXXX b Print :XXXXXX Select ab or OK c Press a or b to choose the option for which you want to see the machine’s page counters for color and black & white. Press OK. 63.Page Counter Total Color :XXXXXX B&W :XXXXXX d Press Stop/Exit. Troubleshooting and routine maintenance Checking the remaining life of parts You can view the remaining life of these parts on the LCD. a Press Menu, 6, 5. 65.Parts Life 1.Drum 2.Belt Unit 3.PF Kit MP Select ab or OK b Press a or b to choose 1.Drum, 2.Belt Unit, 3.PF Kit MP, 4.PF Kit 1, 5.PF Kit 2 1 , 6.Fuser or 7.Laser. Press OK. 65.Parts Life 1.Drum Remaining:100% 1 PF Kit 2 appears only when the optional LT-100CL tray is installed. c Press Stop/Exit. Note The life check of a part will be accurate only if that part’s life counter was reset when the new part was installed. It will not be accurate if that part’s life counter was reset during the life of the used part. C 149 D D Menu and features On-screen programming Your machine has been designed to be easy to use. The LCD provides on-screen programming using the menu keys. We have created step by step on-screen instructions to help you program your machine. Simply follow th...