valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
Cleaning Unit An assembly that cleans any residual image toner from the Drum in preparation for the next image. CLEAR/STOP Key The Key used to stop a copy job while it is still running. It may also be used to clear program functions from a previous job and return to the default settings. Control Panel The surface at the front of the copier containing Keys used to control the operation of the copier. It usually also contains the display that shows the status of the copier or the job in progress. Copies The imaged paper output from a copier. It might be a direct reproduction of the input document or it can contain any number of changes as programmed into the copier such as Enlargement/Reduction, Trim/Mask, etc. Copies in Progress This display or part of a display shows how many copies of the total have been made. Copies Selected This display is the same as Copy Quantity, in that it shows the number of copies requested. Copy Paper See: paper Copy Quantity This display or part of a Touch Screen shows the requested number of copies. Copy Size Keys Keys used to input the desired size of the copy. Darker Copies This term refers to the amount of toner placed on the copy through the imaging process. The amount of toner is controlled by the “darkness” of the original and the amount of light used during the exposure process; more light means less toner or image density. Developer Material This is a supply used in the copier. It usually consists of two parts; a carrier material and the toner. The developer material is only used by a technician when installing a new unit or when cleaning a Developer Unit. Developer Unit An assembly located near the drum inside the copier that delivers the toner to the drum. It allow the correct amount of toner to be placed on the drum for each image. Document Feed Tray The Tray where an original document is placed to feed into an ADF for automatic feeding and copying. Document Guide These Guides are located in the Document Feed Tray. When correctly positioned against the sides of an original document, they help to position the pages of the document. Document Receiving Tray A Tray used to accumulate the pages of an original document that have completed the copying process. Document Scale Two scales located to the front and left of the Exposure Glass intended to help locate original documents placed on the Glass for manual copying and to identify a part of an original during the Editing process. Documents The set of pages either placed on the Exposure Glass or in the ADF to be copied. Drum Assembly The unit located inside the copier that receives the image during the exposure and imaging process and transfers this image to the copy paper. It is light sensitive and should be protected from bright lights. Energy Saver Key A Key used to place the copier into, or bring it out of an Energy Saver Mode. In the Energy Saver Mode, the amount of energy consumed by the copier is reduced. Energy Star A voluntary program introduced by the United States Environmental Protection Agency (EPA) intended to encourage the use of energy- efficient technologies in the workplace. Requirements to qualify for certification vary based on the speed of a Copier. For specifics on your Copier, check the Specifications section of this Guide. Exit Tray A tray attached to the output end of the copier to collect copies. This tray is usually removed when a Sorter or Finisher is installed. In this case, the top tray of the Sorter or Finisher serves as the Exit Tray. Exposure Glass The glass surface located under the Document Cover or Document Feeder. The original is placed here to make a copy. If an RADF is present, it transports the original to this location. Once here, the original is exposed by the Exposure Lamp located directly below the glass. Exposure Lamp The light source located directly below the Exposure Glass. It is the light from this lamp that exposes the original, reflects off the original, travels through the optics and exposes the Drum. Exposure Pad A Pad located on the bottom side of a Document Cover used to hold an original in place on the Exposure Glass during the exposure process. Factory Default A setting in the copier that is set at the factory. You can change some of these settings. Others can be changed by a Service Technician. See also Initial Setting. Front Cover The Cover located at the front of the copier designed to allow access to the interior of the copier. This allows the operator to add supplies, remove paper misfeeds, or perform other maintenance as prescribed by the Operator Guide. Fused Toner The image, usually black, that adheres to the surface of the copy paper. This Toner is “Fused” to the surface of the paper using pressure and heat. Fuser Assembly The unit located inside the exit area of the copier that provides heat and pressure to attach the toner to the paper surface. Fuser Cleaning Pad In certain copiers, it is necessary to clean toner residue and paper dust from the Fuser Roller...