Factory default settings are underlined. To make settings that are not provided in the chapter, you can design custom bar codes or use the Falcon Management Utility (FMU) to program the Falcon. Refer to Configuring the Falcon, on page 2-1. 1D Symbologies Symbologies and bar code setup parameters included in this appendix are: • "Predefined Defaults" on page G-3. • "Codabar" starting on page G-3. • "Code 39" starting on page G-5. • "Code 93" starting on page G-8. • "Code 128" on page G-10. • "EAN

To define a new Hot Key, complete the following steps: 1. Enter the key combination to define a new Hot Key in the Enter Key textbox. 2. The Note displays important information indicating Hot Keys that should not be used. Product Reference Guide Falcon® Desktop Utility for Windows® CE Figure B-5. Add a New Hot Key Table B-6. Adding a New Hot Key Dialog Command Description Enter Key Enter the desired key combination in this text box to define a Hot Key. OK Select/tap OK to add the specified Hot K

This setting pertains only to units configured for EAS Coupled Mode. Reference the “EAS Mode ” description for more information about Coupled and Decoupled EAS operation. Also reference “EAS Retry Count .” NOTE To set the EAS Deactivation Duration — Manual: 1. Scan the SWITCH bar code. 2. Scan the bar code, SET EAS DEACTIVATION DURATION — MANUAL below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. 3. S

See Chapter 4, Scale Error Reporting, if vibration is suspected of causing operational problems. Installation Overview The preceding Site Preparation Overview dealt with installed location and counter preparations to accommodate the scanner or scanner/scale. Having completed those steps, physical installation of the scanner or scanner/ scale can begin. The following instructions apply to all models. This chapter describes: 1. Unpacking the unit. 2. Verifying operation before connecting to a POS

On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety. Basee sur la legislation des Etates membres relative a la compatibilite electromagnetique et a la securite des produits. Uber die Annaherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Vertraglichkeit und Produktsicherheit entsprechen. Basado en la aproximacion de las leyes de los Paises Miembros respecto a la compatibilidad electromagnetica y las Medidas de seguri

reserves the right to make modifications and improvements without prior notification. Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or consequential damages resulting from the use of this material. Product names mentioned herein are for identification purposes only and may be trademarks and or registered trademarks of their respective companies. © Datalogic S.p.A. 2002-2006 821000631 (Rev. A1) CONTENTS GUIDE TO INSTALLATION ....

They are used together and they have the following significance: when a jumper is in the J1 position (see Figure above) pin 40 is connected to pin 27 (EXT TRIG+); a jumper in J2 position connects pin 20 to pin 28 (EXT TRIG-). If the jumpers are removed pin 20 and pin 40 are disconnected. Casella di testo: to EARTH GROUND (default) Casella di testo: to GND Casella di testo: floating Casella di testo: J2 Casella di testo: J1 2.5 PROFIBUS CONNECTIONS AND SETUP 2.5.1 Profibus Node Address Selection

FED B A C Figure 1 – Datalogic Jet ™ Ethernet Multi Cradle General View Key: A) Link LED for Ethernet Port 1 B) Speed LED for Ethernet Port 1 C) Datalogic Jet™ Charging Status LED D) Power supply connector E) Ethernet Port 1 (with integrated Link and Speed LEDs) F) Ethernet Port 2 (with integrated Link and Speed LEDs) 822000751 (Rev. A) The Ethernet cradle drivers are pre-installed on the Datalogic Jet™ and initiate automatically when the Datalogic Jet™ is placed in a properly connected Four Slo

Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or consequential damages resulting from the use of this material. Product names mentioned herein are for identification purposes only and may be trademarks and or registered trademarks of their respective companies. © Datalogic S.p.A. 2001 - 2003 820000884 (Rev. D) CONTENTS INTRODUCTION................................................................... v COMPLIANCE ..................

Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic medium or machine readable form without prior written consent of Datalogic. Limited Warranty Under all circumstances this manual should be read attentively, before installing and/or using the pro-duct. In no event Datalogic will be liable for any direct, indirect, special, consequential or incidental damages arising out of the use or inability to use t