valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
This requires a minimum distance of 600mm between cupboard units of hotplate height. When installing next to a tall cupboard, partition or wall, for a minimum distance of 400mm above hotplate level, allow a side clearance of at least 65mm. The diagram below illustrates the minimum clearance between the cooker and adjacent walls, cupboards etc. The wall behind the cooker, 50mm below and 450mm above, and the width of the cooker, must be a non-combustible material such as ceramic wall tiles. If the cooker is to be fitted close to a corner on the left hand side, ensure that there is a clearance of at least 50mm to allow the main oven door to open fully for when removing oven shelves. 65 mm Min400 mm Min750mm min 600 mm Min COOKER HOODS If a cooker hood is to be installed, refer to the cooker hood manufacturers’ instructions regarding fixing height. INSTALLATION INSTRUCTIONS UNPACKING THE COOKER Unpack the components from inside the grill and oven: Check that the following parts are present. Grill pan and grid Top oven/grill shelf heat shield Baking dish Pan supports Main oven shelves (2) Enamelled burner caps (4) Top oven/grill shelf (1) Literature Aluminium burner bodies(4) LEVELLING Four skid feet are fitted which can be adjusted up or down to level the cooker. CONVERSION FOR USE ON BUTANE (G30) OR PROPANE (G31) Each burner requires the injector to be replaced and bypass screws adjusted or replaced as follows: 1. Remove the loose hotplate burner parts. 2. Using a 7mm socket, replace the hotplate injectors as appropriate (see table on previous page). 3. Re-position the loose burner parts. 4. Remove the enamelled baffle at the front of the grill (2 screws). 5. Remove the screw on the right hand side of the burner and gently slide the burner off the injector. 6. Using a 7mm socket, replace the grill injector as appropriate (see table on previous page). 7. Re-assemble the burner and baffle. 8. Inside the top oven, remove the central screw securing the burner retainer. Slide the retainer to the right slightly and lift away. 9. Lift the burner assembly and place on the floor of the oven to the right of the burner opening. 10. Using a 7mm socket, replace the oven injector as appropriate (see table on previous page). 11. Re-assemble the oven burner and retainer. 12. Replace the main oven injector following the same procedure as for the top oven. 13. From behind the cooker, remove the screws securing the rear panel and swing the left hand side outwards (viewed from the rear) to gain access to the main oven flame supervision device. 14. Replace the flame supervision device bypass screw. 15. Re-assemble the rear panel. 16. Carefully pull off the control knobs and timer buttons. 17. Remove the 2 screws securing the underside of the control panel. Slide the control panel to the left slightly to remove. continued... INSTALLATION INSTRUCTIONS 18. Remove the 6 screws securing the timer mounting panel. Without completely removing it, manoeuvre the timer mounting panel to gain access to the thermostat bypass screws. 19. Using a narrow flat bladed screwdriver rotate the bypass screws fully clockwise. The main oven thermostat bypass screw is located on the body of the thermostat below the spindle, the top oven thermostat bypass screw is located on the body of the thermostat to the right of the spindle and the hotplate tap bypass screws are located down the centre of the spindle. 20. Re-assemble the control panel parts. 21. Secure the self-adhesive LPG conversion label over the gas details on the data badge. STABILITY CHAIN A hole in the gas inlet valve bracket can be used to engage a stability chain. CONNECTING TO GAS SUPPLY 300 670 Connection to the cooker should be made with an approved appliance flexible connection to BS 669. A length of 0.9 to 1.25m is recommended. The length of hose chosen should be such that when the cooker is in situ, the hose does not touch the floor. Those cookers converted to use on LPG should be connected with a hose suitable for LPG and capable of withstanding a pressure of 50 mbar. An adaptor backplate should be fitted within the shaded area shown, to allow the cooker to be pushed fully to the wall and to ensure that the flexible hose is only likely to come into contact with areas at the rear of the cooker that do not exceed a temperature rise of 70°C. ELECTRICAL CONNECTION WARNING – THIS APPLIANCE MUST BE EARTHED. CONNECT TO A 230-240V A.C. SUPPLY ONLY. Connection to the electricity supply should be made via a properly earthed, readily accessible wall socket which is adjacent to but not directly above, and not more than 1.25m away from the appliance and capable of electrical isolation. The mains lead should be routed such that it cannot touch hot parts of the cooker i.e. the back panel above a height of 650mm from the floor. Should this plug not fit the socket outlet in your home it should be cut off and replaced with a suitable plug as outlined below. NOTE: The removed plug cannot be used for any ...
Questo manuale è adatto anche per i modelli :Pentole a pressione - Chesterfield Traditional 60 C60GT (326.96 kb)