valutazioni - 2, GPA: 3.5 ( )

Produttore : Country Home Products File Size : 429.64 kb File Nome : Lingua di insegnamento:

Where it is possible to throw the snow to the left and right (above), as on a long driveway, it is advantageous to start in the middle. Plow from one end to the other, throwing snow to both sides without changing the direction of the discharge chute. If the snow can only be thrown to one side of the driveway or sidewalk (above), start on the opposite side. At the end of the first pass, rotate the discharge chute 180 degrees for the return pass. At the end of each succeeding pass, rotate the discharge guide 180 degrees to maintain direction of throw in the same area. DR® SNOW THROWER Safety, Operation & Maintenance Instructions MAINTENANCE ALWAYS USE GENUINE PARTS WHEN Drive Belt Replacement (Figure 4, REPLACEMENT PARTS ARE REQUIRED Page 12) ! WARNING: Never park the DR® ALLTERRAIN ™ MOWER with fuel in the fuel tank inside a building where an open flame or sparks are present. Allow the engine to cool down before storing in any enclosure. ! WARNING: Provide adequate blocking before working under the DR® SNOW THROWER. ! WARNING: Run the DR® SNOW THROWER a few minutes after throwing snow to prevent freeze up of auger. Drive Chain Replacement (Figure 10) Replace the chain when the distance between the sections of the chain (item 1) is reduced to 2" (see figure). ! WARNING: Always disconnect the spark plug wire before servicing your machine. 1. Unbolt the chain cover (item 2) and remove it. 2. Remove the connecting link on the chain, and remove the chain. 3. Check the chain tensioner (item 5) for wear. Replace if necessary. 4. Install the new chain around the sprockets (items 3 & 4). 5. Pull the tensioner (item 5) and install the connecting link on the new chain. 6. Release the tensioner on the chain. 7. Lubricate the new chain with chain saw lubricant. 8. Reinstall the cover. When the belt tensioner is 1/8" close to its support (see figure below) due to belt elongation or after the equivalent of 60 hours of continuous operation, replace the drive belt. ! WARNING: Always disconnect the spark plug wire before servicing your machine. 1. Remove the bolts (item 5) to remove the belt cover (item 4). 2. Pull the tensioner (item 3) and remove the belt (item 1) from the pulleys. 3. Install the new belt in the same pathway as the old one. 4. Re-engage the tensioner. 5. Reinstall the belt cover with the bolts. Figure 10 DR® SNOW THROWER Safety, Operation & Maintenance Instructions MAINTENANCE Shear Bolt Replacement (Figure 11) If you strike a foreign object (wood, stone, etc.) there is a safety shear bolt on the driving system. This shear bolt will break, eliminating any driving force to the auger. ! WARNING: Always disconnect the spark plug wire before servicing your machine. 1. To replace the shear bolt, stop the DR® ALL-TERRAIN™ MOWER and remove the spark plug wire. 2. Remove the bolts (item 1), and remove the belt cover (item 2). 3. Make sure that there is no debris remaining in the shaft hole. 4. Align the pulley hole with the shaft hole (item 3) and install the new shear bolt and nut (item 4). Tighten securely. 5. Reinstall cover and bolts. Lubrication ! WARNING: Always disconnect the spark plug wire before servicing your machine. Lubricate the drive chain with chain saw chain lubricant every 2 hours of operation and also after each use. Storage Before storing the DR® SNOW THROWER, certain precautions should be taken to protect it from deterioration. ! WARNING: Always disconnect the spark plug wire before servicing your machine. 1. Clean the DR® SNOW THROWER thoroughly. 2. Make all the necessary repairs. 3. Repaint all parts from which paint has worn or peeled. 4. Lubricate the DR® SNOW THROWER as instructed under Lubrication. 5. When the DR® SNOW THROWER is dry, lubricate all moving parts. Apply Fluid Film® or comparable lubricant liberally to all surfaces to protect against rust. 6. Store in a dry place. Figure 11 DR® SNOW THROWER Safety, Operation & Maintenance Instructions SPECIFICATIONS Country Home Products Single Stage DR® SNOW THROWER Overall width 30 1/2" Overall height (without chute) 19 1/2" Overall height (with chute) 37 1/2" Overall length 29 1/8" Cutting width 29 3/4" Cutting height 18 1/4" Frame thickness 16 Ga. Side thickness 12 Ga. Number of stages 1 Drive 'B'' type belt and ''B'' type pulley Drive pulley 5 3/4" O.D. Idler belt adjustment Automatic spring tensioner Auger drive # 40 chain and sprocket...

Scarica la tua

Per scaricare, digitare 2 cifre :