valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
BEFORE OPERATION Check the General Conditionof the Snowblower: Look around and underneath the snowblower for signs of oil or gasoline leaks. Checkthe augerhouse and the discharge chute for accumulation of packed snow or ice. Clean the auger housing and discharge chute before starting the snowblower. Look for signs of damage. Check each control for proper operation. Check the auger and blower for loose or broken bolts,If broken, replace them with new ones (page49). Check the skid shoes and scraper bar for wear. Replace them if necessary (page 50). Check that all nuts, bolts, screws are tightened. Check the Engine Check the oil level (page 40). Check the fuel level (page 38). Starting with afull tank will help to eliminate or reduce operating interruptions for refueling. Check the hydrostatic fluid level in thereservoir (page 43). Useonly HONDA HYDROSTATIC FLUID. 19 BEFORE OPERATION CHECK YOUR WORK AREA For your safety and the safety of others, always inspect the area before operating the snowblower. Objects Anything which can be picked up by the augers and thrown is a potential hazard to you and others. Look for things like stones, sticks, bones, nails, and wire, and remove them from the work area. People and Pets People and animals near the work area can move into your snowblowers path or into a position where they could be struck by thrown objects. Clear the area of people, especially children and pets. Their safety is your responsibility. Work Area Check the condition of the snow. Adjust your snowblower ground speed (not engine speed) and snowblowing swath accordingly. Check the skid shoes for proper adjustment. Adjust the skid shoes to obtain the auger ground clearance for the type of surface the snowblower will be operated over (page 51). OPERATION SNOWBLOWING PRECAUTIONS Before operating the snowblower for the first time, please review both the SNOWBLOWER SAFETYchapter (page 5) and the BEFORE OPERATION chapter (page 18). Even if you have operated other snowblowers, take time to become familiar with how this snowblower works, and practice in a safe area until you build up your skills. Never tamper with, oralterany of the controls or safety devices on the snowblower. For your safety, avoid starting or operating the engine in an enclosed area such as a garage. Your snowblower’s exhaust contains poisonous carbon monoxide gas which can collect rapidly in an enclosed area and cause illness or death. Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any areas that expose enclosed or activities you to carbon monoxide. STARTING THE ENGINE 1. Move the shift lever to “N” (Neutral) position. i I I N (Neutral) OPERATION 2. Set the transmission release lever ENGAGED in the ENGAGED position (page 16). TRANSMISSIONRELEASE LEVER 3. Turn the fuel valveto the ON position. Besurethatthedrainknobis tightened securely. \ DRAIN KNOB THROlTLE LEVE 4. In coldweather and when the engine is cold, follow the procedures below. HS624/HS724/HS828/HS928: Move the throttle lever to the CHOKE position. / CHOKE OPERATION HS1132: Pull the choke knob to the CLOSED position and move the throttle lever to the FAST position. CHOKE KNOB eCLOSED THROTTLE LEVER 5. Start the engine. Electric-start Models (TAS, WAS type): a. Connect your power cord to the switch box and the male end of the power cord to a properly grounded 120 volt ac outlet. I ACAUTION I IUSE ONLY WITH GROUNOEO OUTLET AN0 3-WIRE CORD. 1120 VOLT A.C. ONLY 100 NOT CRANK OVER 1 MINUTEWllHOLlT COOLING 15 MINUTES. 100 NOT USE INRAIN. I POWER CORD To minimize the possibility of potentially dangerous electrical shocks, always use a 3-conductor power cord with a power rating of no less than 15 amps. Also, be sure that the outlet you are using is properly grounded. Do not connect and disconnect the power cord with wet hands. Be sure to hold the plug when disconnecting the power cord from the electrical outlet or switch box. Do not disconnect by pulling on the power cord. OPERATION b. Turn the engineswitch to the ON position. ON I I\I c. Push the starter button until the engine starts. After the engine starts, disconnect the power from cord the electrical outlet, and then from the switch box. Do not operate the starter for more than 1 minute. If the engine fails to start, release the button and allow the starter to cool for 15 minutes before operating it again. Manual Starting only a. Pull the starter grip lightly until you feel resistance, then pull briskly. b. Return the starter grip gently to the engine. piEq Do not allow the startergrip to snap back against the engine. Return it gently to prevent damage to the starter. Do not pull the starter grip while the engine is running. The starter could be damaged. OPERATION 3. Let the engine warm up for several minutes. HS624/HS724/HS828/HS928: If the throttle lever has been movedto the CHOKE position, gradually move the throttle lever to the SLOW position as the enginewarms up. HS1132: If the choke ...