valutazioni - , GPA: ( )

Istruzioni per l'uso Ariens, Modello 926001-ST926LE

Produttore : Ariens
File Size : 7.4 mb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Oil Fill and Drain Plug 3.Auger Gearcase - Aluminum 3 2 1 OS7130 GB - 21 GENERAL LUBRICATION IMPORTANT: Wipe each fitting clean before and after lubrication. Do not wipe gearcase filler plug; wiping the gearcase filler plug may remove thread sealant and cause leaks. IMPORTANT: DO NOT allow grease or oil to get on friction disc, friction plate or belts. NOTE: Apply Stens Mix Hi-Temp Grease or equivalent to the lubrication fittings. See SERVICE PARTS on page 29. Sno-Thro should be lubricated (Figure 18) at beginning of season or every 25 operating hours. Auger Shaft NOTE: To grease auger shaft, remove shear bolt nuts, and shear bolts. Turn auger on shaft while applying grease at zerk fittings. Replace shear bolts per instructions in SERVICE AND ADJUSTMENTS on page 22. CLEAN BATTERY (926500, 501) IMPORTANT: Battery is maintenance-free. Do not tamper with or attempt to open battery. See SERVICE AND ADJUSTMENTS on page 22 for charging procedures. Terminals Keep battery and its terminals clean. IMPORTANT: Remove battery from unit before cleaning. Remove corrosion from battery terminals and cable connections with a wire brush, then wash with a weak baking soda solution. After cleaning, apply a thin coat of grease or petroleum jelly to terminals and cable ends to retard corrosion. WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. 1 1 Figure 18 2 1 1 Grease Oil OS0642 OS7135 OS7140 OS7150 SERVICE AND ADJUSTMENTS SERVICE AND ADJUSTMENTS WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. RUNNERS Runners should be adjusted as conditions require (Figure 19). 1. Position unit on a hard, flat, smooth level surface. 2. Adjust runners by inserting a spacer of desired thickness under center of scraper blade, loosen runner hardware, slide runners to flat surface. Allow 1/8 in. (3 mm) between scraper blade and hard smooth surfaces. Allow 1-1/4 in. (30 mm) between scraper blade and uneven or gravel surfaces. Retighten hardware. NOTE: Keep housing level by adjusting runners equally. 1 1.Runner 2.Runner Hardware OS0482 Figure 19 SCRAPER BLADE IMPORTANT: Damage to auger/impeller housing will result if blade wears down too far. Scraper blade is adjustable to compensate for wear. To adjust scraper blade: 1. Tip unit back onto handlebar, support housing and loosen nuts retaining blade. 2. Adjust runners to fully raised position (housing closest to ground). 3. Reposition scraper blade flush with runners and tighten lock nuts. SHEAR BOLTS IMPORTANT: Use only Ariens shear bolts for replacement. Use of any other type of shear bolt may result in severe damage to unit. Occasionally a foreign object may enter the auger/impeller housing and jam the auger, breaking shear bolts (Figure 20) which secure the auger to the shaft. This allows auger to turn freely on the shaft preventing damage to gear drive. Figure 20 1. Auger 2. Shear Bolts 1 2 OS7150 2 For Replacement: 1. Align shear bolt holes in auger with shear bolt holes in the shaft. 2. Drive shear bolt through hole (if shear bolt was broken this will drive remaining part from shaft). 3. Secure shear bolt with nut. HANDLEBAR HEIGHT CAUTION: AVOID INJURY. Adjust the attachment clutch, speed selector and traction clutch after changing the handlebar height. See Attachment Clutch/Brake Adjustment on page 25, Speed Selector Adjustment on page 25 and Traction Drive Clutch Adjustment on page 26. To raise or lower the handlebar: 1. Remove hair pin holding chute rod to control assembly. 2. Place unit in service position (see Service Position on page 19). 3. Remove bottom cover. 4. Remove top mounting bolts from the handlebars and adjust the handlebar up or down as needed until the handlebar mounting holes align with holes in unit frame. 5. Secure handlebar to frame with hardware removed in step 4 using the different hardware locations shown in Figure 21. GB - 22 GB - 23 NOTE: Insert the hair pin with the loop end on the left side of the chute rod so the control lever will cover its full range of travel. 6. Align correct chute rod holes in chute control assembly as shown in Figure 22, and then secure chute rod in position with hair pin remove in step 1. 7. Check and adjust attachment clutch, speed selector and traction clutch. See Attachment Clutch/Brake Adjustment on page 25, Speed Selector Adjustment on page 25 and Traction Drive Clutch Adjustment on page 26. 8. Re-install bottom cover. REMOTE DIFFERENTIAL (926004, 005, 006, 300, 301, 500, 501) If remote differential does not lock: 1. Place unit in service position (see Service Position on page 19). 2. Remove bottom cover. 3. Loosen jam nuts on cable. Make sure the bottom jam nut is loosened enough to remove slack from cable. 4. Pull the cable adjuster to remove slack between the cable adjuster and the extension spring and hold the cable adjuster in position while tightening the top jam nut against the unit frame. Do not extend the spring or engage the mechanism. 5. Tighten t...