valutazioni - 5, GPA: 4.2 ( )

Produttore : Ariens File Size : 1.75 mb File Nome : Lingua di insegnamento:

IMPORTANT: If the belt squeals when the 1OL2691 attachment clutch lever is engaged, the attachment drive may be frozen. Immediately release the attachment clutch lever and move the unit into a heated area to thaw. Ignition Switch (120V start on engine) Key Switch has two positions: 1. “Stop” - pulled out 2. Run - pushed in 2 NOTE: DO NOT twist key after it is inserted. 1 OS1431 Ignition Switch (12V start on dash panel) 2 3 The ignition switch is operated by a removable key. It has three positions: 1.Stop 2.Run 3.Start OS0232 Primer Bulb OS1321 Pushing the primer bulb in adds fuel for easier engine start. Refer to Starting and Shut Off. The Speed Selector controls the unit travel in a forward or reverse direction when positioned in notch of speed. Forward: OS1191 6 5 4 3 2 1 (6) Fastest (1) Slow Reverse: (1) Slow (2) Fast IMPORTANT: DO NOT change motion from forward to reverse with clutch engaged. Forward speed can be changed without 1 declutching. 2 Choke Control Knob 1. Choke Closed position: chokes off air to engine for easier start. 21 2. Choke Open position: allows for normal operation. IMPORTANT: Gradually open choke after engine OS1332 starts. Throttle STOP The throttle controls the engine1 speed. To increase or decrease the engine speed, adjust to: 2 1. Fast (normal or warm starts) 2. Part-Throttle 3. Slow (cold weather starts) 3 4. Stop (engine is off) 4 OL2720 Electric Starter The electric starter will start a properly choked and cranked engine when the key is turned (12V) or starter button (120V) is pushed. Refer to Starting and Shut-Off. Recoil Starter Handle When pulled, handle will turn engine over. IMPORTANT: DO NOT let handle snap back against starter. GB - 15 Discharge Chute Deflector Discharge Chute Deflector a safe angle before starting engine. DO NOT throw snow any higher than necessary. Push deflector handle forward or down to throw snow lower. Pull deflector handle up or to the rear to throw snow higher. IMPORTANT: If Chute Deflector does not stay in set position, adjust as directed in Service and Adjustments, or repair before operation. Deflector Remote (924121, 332, 505, 506) Place deflector into position before operation. DO NOT throw snow any higher than necessary. Push deflector remote forward to throw snow lower. Pull deflector remote back to throw snow higher. Discharge Chute Discharge chute rotates 220°. ALWAYS position discharge chute in safe direction and angle, away from operator and bystanders, before starting engine. Chute Crank (924121, 122, 332, 508) IMPORTANT: If chute does not stay in set position, adjust as directed in Service and Adjustments, or repair before operation. Rotate the Chute with Discharge Chute Crank Handle. IMPORTANT: DO NOT force frozen chute controls. Start engine and run for 3-5 minutes to thaw. If still frozen, take to warm place until controls are free. Chute Rotation Switch (924505, 506) 12 OS1970 Press the chute rotation switch right (1) to rotate chute clockwise. Press the chute rotation switch left (2) to rotate chute counterclockwise. Heated Handles 1 2 OS1950 Turn the heated handles switch to the ON (1) position to activate. Turn the switch to the OFF (2) position to deactivate. Differential Lock (924118, 122, 332, 505, 506, 508, 551) 1 2 Differential Lock knob is located on the Left Wheel Hub. With differential locked power is applied equally to both wheels. To engage differential lock: • Pull and turn knob to LOCKED (1) position and release (knob will snap in place when positioned correctly). OL2730 To resume differential action for transport: • Pull and turn knob to UNLOCKED (2) position and release. Axle Lock Pin (Figure 9) (924121) Figure 9 Wheel Unlocked Wheel Locked Axle Lock Pin Use the axle lock pin to lock or unlock the right wheel. Lock the right wheel to increase traction; unlock the right wheel to allow for easier turning of the unit. GB - 16 Scraper Blade Scraper Blade IMPORTANT: DO NOT allow Scraper Blade to wear too far or Auger/Impeller housing will become damaged. Runners The runners control the distance between the scraper blade and the ground. Adjust runners equally to keep blade level with the ground. Refer to Pre-Start for recommended settings. FILLING FUEL TANK WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. Fuel Shut-Off Valve IMPORTANT: The fuel shut-off valve MUST be in the closed position prior to transporting the unit. The fuel shut-off valve has two positions: • Closed Position: Use this position to service, transport, or store the unit. • Open Position: Use this position to run the unit. To add fuel to fuel tank: 1. ALWAYS place unit in open or well ventilated area. 2. Stop engine and allow to cool. 3. Clean Fuel Cap and surrounding area to prevent dirt from entering Fuel Tank. 4. Remove Cap. IMPORTANT: DO NOT use gasohol or gasoline containing alcohol. See Engine Manual for correct type and grade of fuel. 5. Fill fuel tank to within 1/2 in. (1.2 cm) below bottom of filler n...

Scarica la tua

Per scaricare, digitare 2 cifre :