valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
At point of resistance, pull rapidly and vigorously. Maintain control of rope so it slowly returns into starter mechanism. Repeat pulling actions until engine starts. C. Gradually move choke knob to NO CHOKE as engine warms up. For optional 110V electric starter: A WARNING • DO NOT use 110V electric starter during rainy weather. • DO NOT stand in puddles or on damp surfaces when connecting cord. • DO NOT run engine indoors or in poorly-ventilated areas. A. Plug electrical cord into switchbox on top of engine. B. Plug other end of electrical cord into a properly grounded 110V outlet. C. Push starter button on top of switchbox. As soon as engine starts, release button. NOTE: Starter is thermally protected. When overheated from continuous use, starter will automatically stop functioning. Allow starter to cool for several minutes before making further attempts to start engine. D. After engine starts, gradually move choke knob to NO CHOKE as engine warms up. Testing Auger and Wheel Drive A WARNING PERSONAL INJURY HAZARD. • DO NOT use snowthrower if auger spins before you squeeze auger drive lever. • DO NOT use snowthrower if auger continues to spin after you release auger drive lever. 1. To test auger drive, squeeze and release auger drive lever. Auger should begin spinning when lever is squeezed and stop spinning when lever is released. 2. To test wheel drive, shift into first gear. A WARNING PERSONAL INJURY HAZARD. • DO NOT use snowthrower if wheels turn before you squeeze wheel drive lever. • DO NOT use snowthrower if wheels continue to turn after you release wheel drive lever. 3. Squeeze and release wheel drive lever. Wheels should begin turning when lever is squeezed and stop turning when lever is released. 4. Move gear shift lever to desired gear. Starting in first gear is not necessary. 4. If both handlebar levers operate properly, re-engage and begin operation. NOTE: To move unit without throwing snow, engage wheel drive lever. Leave auger drive lever disengaged (released) while moving. Stopping To quickly stop snowthrower: 1. Release both handlebar levers. 2. Turn ignition key to OFF position. To stop snowthrower (normal conditions): 1. Release both handlebar levers. 2. Move throttle lever to idle position. Allow engine to run at idle for several minutes to melt snow off engine. To help avoid possible freezing of starter when snowthrower is not in use: 1. For pull start engines: With engine OFF, pull recoil starter rope all the way out. Repeat 3 or 4 times. For engines with 110V electric start kit installed: A. Connect electrical cord to switchbox. B. Connect other end of cord to 110V outlet. C. With engine OFF, push starter button and spin starter for several seconds. D. Disconnect electrical cord from outlet, then from switchbox. 2. Turn ignition key to OFF. 3. Disconnect spark plug wire and prevent it from touching spark plug. To help avoid possible freezing of controls: 1. Wipe engine of all snow and moisture in, on, near and around throttle control lever linkage and choke knob. Spray linkage and levers with a non-silicone lubricant. 2. Move throttle control lever and choke knob back and forth several times. 3. Move choke to FULL CHOKE and leave in this position. 4. Move throttle to start position and leave it there. 5. Close fuel valve located beneath fuel tank. Changing Gears Begin operating in any gear, including reverse. Shifting from first gear through fifth is not necessary. 12 A CAUTION Unit must be completely stopped while shifting. Damage to transmission will result if this instruction is not followed. • DO NOT shift while in motion! DO NOT shift from one gear into any other with unit in motion. Damage to transmission may result. Allow unit to stop completely before shifting into any other gear, especially before shifting into reverse. To shift into reverse: 1. Release both handlebar levers (auger drive wheel drive levers). Allow unit to come to a complete stop. 2. Move gear control lever into reverse. A CAUTION Failure to follow this instruction could result in personal injury or property damage. • Before engaging wheel drive lever, look behind for and avoid obstacles. 3. Slowly begin squeezing wheel drive lever and guide unit rearward. 4. Allow unit to stop completely before shifting into a forward gear. Before shifting to another gear, release handlebar levers. Allow unit to stop completely. Then, move gear control lever re-engage wheel drive lever. Wheel drive lever may be engaged with gear control lever in any gear, including reverse. Snowthrowing Tips Run engine at full throttle when throwing snow. Use slower wheel speed (first or second gear) in heavy, wet snow. Spray auger, inside auger housing, inside discharge chute and inside deflector chute with silicone spray to help prevent snow from sticking. Inspect operating area before snowfall. Remove all objects from surface such as rocks, mats, boards, wires, nail...
Questo manuale è adatto anche per i modelli :Sgombraneve - 1026 (2.73 mb)